Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren detects this and sounds its siren.

Although the theft warning siren usually sounds by receiving a signal from the main body ECU (multiplex network body ECU), the theft warning siren can sound by its internal battery in case the vehicle battery cable is disconnected.

The main body ECU (multiplex network body ECU) sends an arming signal to the theft warning siren while transferring to the armed state, and it also sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU (multiplex network body ECU) can cause the theft warning siren to sound by sending an alarm signal during the alarm sounding state.

WIRING DIAGRAM

B312497E02
1.76,0.25 2.594,0.458 0.833,0.208 10 from Battery 3.469,0.438 4.667,0.698 1.198,0.26 10 ECU-B NO.1 1.188,1.604 1.344,1.802 0.156,0.198 10 2 1.396,1.771 1.844,1.99 0.448,0.219 10 GND 1.333,2.688 1.781,2.906 0.448,0.219 10 M8 1.344,2.865 3.344,3.104 2,0.24 10 Theft Warning Siren Assembly 3.427,1.75 4.01,2 0.583,0.25 10 CONT 3.573,1.26 3.865,1.479 0.292,0.219 10 +B 3.906,1.146 4.063,1.344 0.156,0.198 10 5 3.906,1.635 4.063,1.833 0.156,0.198 10 4 5.365,1.625 5.656,1.823 0.292,0.198 10 18 5.635,1.76 6.25,1.958 0.615,0.198 10 SSCL 5.479,2.927 6.094,3.125 0.615,0.198 10 G79 5.469,3.094 7.115,3.458 1.646,0.365 10 Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

If the theft warning siren assembly is replaced, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn2 Theft warning siren ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn2
50004 123 35
OK:

The theft warning siren assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - BATTERY AND BODY GROUND)
a.
B298276C02
1.49,0.073 1.938,0.333 0.448,0.26 2.021,1.302 2.51,1.729 false 1.427,1.302 1.042,1.729 false 0.74,1.656 1.135,1.833 0.396,0.177 10 GND 2.521,1.656 2.74,1.833 0.219,0.177 10 +B 1.615,0.125 1.896,0.271 0.281,0.146 10 M8 0.073,0.125 0.469,0.302 0.396,0.177 10 *a
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


Disconnect the theft warning siren assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-5 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the M8 theft warning siren assembly connector.


b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-4 (CONT) - G79-18 (SSCL) Always Below 1 Ω
M8-4 (CONT) - Body ground Always 10 kΩ or higher
G79-18 (SSCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK THEFT WARNING SIREN ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK THEFT WARNING SIREN ASSEMBLY
a.

Temporarily replace the theft warning siren assembly with a new or normally functioning one.

HINT:

Refer to the Service Bulletin.



b.

Check the operation of the theft warning siren assembly function.

OK:

Theft warning siren assembly function operates normally.



Result:
Proceed to
OK
NG



OK

END (THEFT WARNING SIREN ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)