Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048164 IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on [IG]).

·

w/ Theft Deterrent System:

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light.


WIRING DIAGRAM

B278947E23
5.063,1.74 6.719,2.052 1.656,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 2.823,1.781 4.635,2.354 1.813,0.573 10 false Certification ECU (Smart Key ECU Assembly) 2.813,1.635 3.115,1.792 0.302,0.156 10 false G84 0.51,1.594 2.458,2.031 1.948,0.438 10 false Security Indicator Light (Telltale Light Assembly) 0.552,2.49 2.26,2.635 1.708,0.146 10 false : CAN Communication Line 0.521,1.448 0.823,1.604 0.302,0.156 10 false G43 0.792,0.802 1.01,0.969 0.219,0.167 10 false 13 2.979,0.802 3.167,0.958 0.188,0.156 10 false 18 2.042,0.802 2.406,0.958 0.365,0.156 10 false 21 3.198,0.906 3.573,1.063 0.375,0.156 10 false IND 1.042,0.885 1.344,1.042 0.302,0.156 10 false E 1.792,0.896 2.094,1.052 0.302,0.156 10 false LP

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF or ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light illuminates.*2

OK:

The security indicator light is on.



Result:
Proceed to
*1 is NG (*2 is OK)
*2 is NG (*1 is OK) (for LHD)
*2 is NG (*1 is OK) (for RHD)



*1 is NG (*2 is OK)

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

*2 is NG (*1 is OK) (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*2 is NG (*1 is OK) (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-18 (IND) - G43-21 (LP) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
G84-18 (IND) - Body ground Always 10 kΩ or higher
G43-21 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Measure the voltage and check the pulse according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-21 (LP) - Body ground Engine switch off → engine switch on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)