Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A5  Open in Front Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B27A5 Open in Front Floor Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*).
·

Harness or connector

·

No. 1 indoor electrical key antenna assembly (front floor)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in front seat area:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A5 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B320942E54
1.365,0.469 1.958,0.719 0.594,0.25 10 ANTE5 1.417,0.917 1.885,1.104 0.469,0.188 10 CLGB 0.292,1.385 0.688,1.594 0.396,0.208 10 G45 1.896,0.802 2.198,1.115 0.302,0.313 10 3 1.906,0.323 2.01,0.469 0.104,0.146 10 1 5.521,0.458 5.938,0.625 0.417,0.167 10 CLG5 5.521,0.917 5.948,1.073 0.427,0.156 10 CG5B 5.521,1.385 5.698,1.552 0.177,0.167 10 E 5.25,0.271 5.458,0.458 0.208,0.188 10 3 5.25,0.729 5.438,0.917 0.188,0.188 10 2 5.208,1.198 5.406,1.365 0.198,0.167 10 11 5.25,1.833 6.792,2.281 1.542,0.448 10 Certification ECU (Smart Key ECU Assembly) 0.292,1.542 2.521,2.031 2.229,0.49 10 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 5.167,0.917 5.448,1.083 0.281,0.167 10 G84 5.167,0.458 5.531,0.719 0.365,0.26 10 G84 5.167,1.375 5.677,1.677 0.51,0.302 10 G82

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 1 indoor electrical key antenna assembly (front floor) has an antenna coil between ANTE5 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY AND BODY GROUND)
a.

Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-3 (CLG5) - G45-1 (ANTE5) Always Below 1 Ω
G84-2 (CG5B) - G45-3 (CLGB) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
G84-3 (CLG5) or G45-1 (ANTE5) - Body ground Always 10 kΩ or higher
G84-2 (CG5B) or G45-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)
a.

Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.

B271428C30
4.74,0.427 5.125,0.677 0.385,0.25 2.146,0.427 2.531,0.677 0.385,0.25 5.406,1.302 5.76,2.104 false 5.302,1.302 4.969,2.094 false 2.708,1.531 2.448,2.208 false 1.156,2.781 1.365,2.979 0.208,0.198 10 *b 0.156,0.125 0.365,0.323 0.208,0.198 10 *a 1.552,4.365 1.76,4.563 0.208,0.198 10 *c 4.729,2.156 5.208,2.344 0.479,0.188 10 CLG5 4.823,0.479 5.167,0.719 0.344,0.24 10 G84 2.333,4.365 2.542,4.563 0.208,0.198 10 *d 5.563,2.167 6.115,2.354 0.552,0.188 10 CG5B 0.906,3.635 1.323,3.833 0.417,0.198 10 GND 2.375,2.229 2.542,2.427 0.167,0.198 10 E 2.229,0.479 2.646,0.75 0.417,0.271 10 G82
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform
*c Within approximately 30 seconds from when the door is closed *d After approximately 30 seconds from when the door is closed



b.

Connect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G84-3 (CLG5) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)
G84-2 (CG5B) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Instrument Panel Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B27A5 is not output
DTC B27A5 is output



DTC B27A5 is not output

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR] WAS DEFECTIVE)

DTC B27A5 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)