The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage). For the No. 3 indoor electrical key antenna assembly (inside luggage) to detect when the electrical key transmitter sub-assembly is inside the luggage, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the luggage. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B27A7 | Open in Inside Luggage Compartment Electrical Key Oscillator Circuit | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*). | ·
Harness or connector ·
No. 3 indoor electrical key antenna assembly (inside luggage) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
When electrical key transmitter sub-assembly is inside luggage area:
·
Power Source mode does not change when engine switch pressed ·
Electrical key transmitter sub-assembly becomes locked inside vehicle |
- |
| DTC Code | Data List and Active Test |
|---|---|
| B27A7 | Key diagnostic mode can be used to perform troubleshooting |
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The No. 3 indoor electrical key antenna assembly (inside luggage) has an antenna coil between ANTE7 and CLGB terminals.
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G82 and G83 certification ECU (smart key ECU assembly) connectors.
Disconnect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G83-9 (CLG7) - M21-1 (ANTE7) | Always | Below 1 Ω |
| G83-8 (CG7B) - M21-3 (CLGB) | Always | Below 1 Ω |
| G82-11 (E) - Body ground | Always | Below 1 Ω |
| G83-9 (CLG7) or M21-1 (ANTE7) - Body ground | Always | 10 kΩ or higher |
| G83-8 (CG7B) or M21-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G82 and G83 certification ECU (smart key ECU assembly) connectors.
| *a | Component with harness connected
(Certification ECU [Smart Key ECU Assembly]) |
*b | Waveform |
| *c | Before driver door lock sensor touched | *d | After driver door lock sensor touched |
Connect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G83-9 (CLG7) - G82-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
| G83-8 (CG7B) - G82-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage) with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Proceed to |
|---|
| DTC B27A7 is not output |
| DTC B27A7 is output |
DTC B27A7 is not output
DTC B27A7 is output