Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049438 COMBUSTION TYPE POWER HEATER SYSTEM J

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  Power Heater Fuel Pump Circuit  


DESCRIPTION

When the heater switch assembly is turned on, the heater pump assembly receives a drive voltage from the heater assembly. The heater pump assembly provides the heater assembly with fuel necessary for combustion, allowing the heater assembly to operate.

WIRING DIAGRAM

E267498E02
5.302,1.74 5.76,1.938 0.458,0.198 10 A33 5.302,1.906 6.677,2.115 1.375,0.208 10 Heater Assembly 2.698,1.365 3.156,1.563 0.458,0.198 10 A29 2.698,1.542 4.281,1.74 1.583,0.198 10 Heater Pump Assembly 5.427,1.01 5.885,1.208 0.458,0.198 10 L 3.656,1.115 3.896,1.323 0.24,0.208 10 B2 2.844,1.115 3.302,1.313 0.458,0.198 10 E2 2.635,0.885 2.771,1.073 0.135,0.188 10 2 3.938,0.865 4.396,1.063 0.458,0.198 10 1 5.198,0.885 5.365,1.063 0.167,0.177 10 2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER ASSEMBLY - HEATER PUMP ASSEMBLY)
a.

Disconnect the A33 heater assembly connector.


b.

Disconnect the A29 heater pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (L) - A29-1 (B2) Always Below 1 Ω
A33-2 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)
a.
E267499C02
1.521,0.292 1.896,0.521 0.375,0.229 1.906,1.375 2.313,1.375 false 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 1.594,0.333 1.906,0.531 0.313,0.198 10 A29 2.375,1.292 2.688,1.49 0.313,0.198 10 E2
*a Front view of wire harness connector
(to Heater Pump Assembly)


Disconnect the heater pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-2 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT HEATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT HEATER PUMP ASSEMBLY
a.
E267500N01
2.438,1.625 2.198,1.625 2.198,1.625 1.896,1.219 false 0.948,1.615 1.146,1.615 1.146,1.615 1.573,1.208 false 2.5,1.552 2.813,1.75 0.313,0.198 10 B2 0.688,1.531 1,1.729 0.313,0.198 10 E2

Remove the heater pump assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER FUEL PUMP>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (B2) - 2 (E2) Always 9 to 12 Ω



c.

Inspect heater pump assembly operation.

i.

Connect a positive (+) lead from the battery to terminal 1 (B2) and a negative (-) lead to terminal 2 (E2), and check the pressure of the hose by hand.

NOTICE:

This inspection must be done quickly (within 10 seconds) to prevent damage to the heater pump assembly.


OK:

The pressure is applied to the hose.




Result:
Proceed to
OK
NG



OK

4.CHECK HEATER ASSEMBLY

NG

4.CHECK HEATER ASSEMBLY
a.
E267499C03
1.521,0.292 1.896,0.521 0.375,0.229 1.042,1.365 1.531,1.365 true 0.042,0.052 0.354,0.25 0.313,0.198 10 *a 1.594,0.333 1.906,0.531 0.313,0.198 10 A29 0.802,1.292 1.031,1.469 0.229,0.177 10 B2
*a Front view of wire harness connector
(to Heater Pump Assembly)


Disconnect the heater pump assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-1 (B2) - Body ground Engine running
Heater switch assembly on
11 to 14 V
A29-1 (B2) - Body ground Engine running
Heater switch assembly off
Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG