Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049438 COMBUSTION TYPE POWER HEATER SYSTEM C

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  016  Difference Evaluation 2  020  Glow Plug Malfunction  021  Glow Plug Output Overload  022  Glow Plug Output Error  025  Short in K-line Circuit  030  Abnormal Combustion Air Blower Motor Speed  031  Combustion Air Blower Motor Malfunction  032  Short in Combustion Air Blower Motor Circuit  034  Combustion Air Blower Motor Output Error  060  Overheating Control Sensor Malfunction  061  Short in Overheating Control Sensor Circuit  064  Flame Sensor Malfunction  065  Short in Flame Sensor Circuit  071  Surface Sensor Malfunction  072  Short in Surface Sensor Circuit  074  ECU Overheating  090  ECU Internal Malfunction / Reset Detection  091  Repeated Resets Detection  092  ROM Error  093  RAM Error  094  Transistor Malfunction  095  Software Stuck Overflow  096  Operation Locked Detection  097  ECU Defects  098  Main Relay Malfunction  099  EEPROM Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
016 Difference Evaluation 2 The difference in temperatures detected by the surface sensor and control overheating sensor is 30°C (86°F) or higher.
·

Heater assembly (surface sensor)

·

Heater assembly (control overheating sensor)


020 Glow Plug Malfunction Operation stop of the glow plug is detected. (Open in the circuit)
·

Heater assembly (glow plug)

·

Harness or connector


021 Glow Plug Output Overload Overload on the glow plug or a short in the wire harness that is connected to the glow plug is detected.
·

Heater assembly (glow plug)

·

Harness or connector


022 Glow Plug Output Error An error is detected in output from the power heater ECU to the glow plug, or a problem with the wire harness that is connected to the glow plug is detected.
·

Heater assembly (ECU)

·

Harness or connector


025 Short in K-line Circuit A short circuit is detected in the diagnostic communication line in the heater assembly. Heater assembly
030 Abnormal Combustion Air Blower Motor Speed Air blower motor speed is out of the allowable range (8800 rpm to 10400 rpm). (An object may be caught in or between parts around the air blower motor.) Heater assembly (air blower motor)
031 Combustion Air Blower Motor Malfunction Operation stop of the air blower motor is detected. (Open in the circuit)
·

Heater assembly (air blower motor)

·

Harness or connector


032 Short in Combustion Air Blower Motor Circuit A short circuit is detected in the wire harness which is connected to the air blower motor. Harness or connector
034 Combustion Air Blower Motor Output Error An error is detected in output from the power heater ECU to the air blower motor, or a problem with the wire harness that is connected to the air blower motor is detected.
·

Heater assembly (ECU)

·

Harness or connector


060 Overheating Control Sensor Malfunction Operation stop of the control overheating sensor is detected. (Open in the circuit) Heater assembly (control overheating sensor)
061 Short in Overheating Control Sensor Circuit A short is detected in the control overheating sensor circuit.
·

Heater assembly (control overheating sensor)

·

Harness or connector


064 Flame Sensor Malfunction Operation stop of the flame sensor is detected. (Open in the circuit) Heater assembly (flame sensor)
065 Short in Flame Sensor Circuit A short is detected in the flame sensor circuit.
·

Heater assembly (flame sensor)

·

Harness or connector


071 Surface Sensor Malfunction Operation stop of the surface sensor is detected. (Open in the circuit) Heater assembly (surface sensor)
072 Short in Surface Sensor Circuit A short is detected in the surface sensor circuit.
·

Heater assembly (surface sensor)

·

Harness or connector


074 ECU Overheating The heater assembly (ECU) stops operating due to overheating. Heater assembly (ECU)
090 ECU Internal Malfunction / Reset Detection An internal malfunction of the control unit is detected. Heater assembly (ECU)
091 Repeated Resets Detection Reset operation is repeated too many times. Heater assembly (ECU)
092 ROM Error A control unit (ROM) error is detected. Heater assembly (ECU)
093 RAM Error A control unit (RAM) error is detected. Heater assembly (ECU)
094 Transistor Malfunction A transistor malfunction due to frequent operation interruptions is detected. Heater assembly (ECU)
095 Software Stuck Overflow A software stuck overflow is detected. Heater assembly (ECU)
096 Operation Locked Detection An operation lock due to the absence of valid process is detected. Heater assembly (ECU)
097 ECU Defects An internal control unit malfunction is detected. Heater assembly (ECU)
098 Main Relay Malfunction A main relay malfunction is detected. Heater assembly (ECU)
099 EEPROM Error An EEPROM error is detected. Heater assembly (ECU)

PROCEDURE

1.REPLACE HEATER ASSEMBLY

Result:
Proceed to
NEXT



NEXT

END