Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049438 COMBUSTION TYPE POWER HEATER SYSTEM C

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  047  Short in Heater Fuel Pump Circuit  048  Heater Fuel Pump Malfunction  049  Heater Fuel Pump Output Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
047 Short in Heater Fuel Pump Circuit A short is detected in the heater pump circuit.
·

Harness or connector

·

Heater pump assembly

·

Heater assembly


048 Heater Fuel Pump Malfunction Operation stop of the heater pump is detected. (Open in the circuit)
·

Harness or connector

·

Heater pump assembly

·

Heater assembly


049 Heater Fuel Pump Output Error An error is detected in output to the heater pump.
·

Harness or connector

·

Heater pump assembly

·

Heater assembly



WIRING DIAGRAM

E267498E01
5.302,1.74 5.76,1.938 0.458,0.198 10 A33 5.302,1.906 6.677,2.115 1.375,0.208 10 Heater Assembly 2.698,1.365 3.156,1.563 0.458,0.198 10 A29 2.698,1.542 4.281,1.74 1.583,0.198 10 Heater Pump Assembly 5.427,1.01 5.885,1.208 0.458,0.198 10 L 3.656,1.115 3.896,1.323 0.24,0.208 10 B2 2.844,1.115 3.302,1.313 0.458,0.198 10 E2 2.635,0.885 2.771,1.073 0.135,0.188 10 2 3.938,0.865 4.396,1.063 0.458,0.198 10 1 5.198,0.885 5.365,1.063 0.167,0.177 10 2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER ASSEMBLY - HEATER PUMP ASSEMBLY)
a.

Disconnect the A33 heater assembly connector.


b.

Disconnect the A29 heater pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (L) - A29-1 (B2) Always Below 1 Ω
A33-2 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the heater pump assembly connector.


b.
E267499C01
1.51,0.302 1.917,0.531 0.406,0.229 1.833,1.417 2.156,1.531 2.156,1.531 2.333,1.531 true 1.573,0.344 2.031,0.542 0.458,0.198 10 A29 0.042,0.042 0.5,0.24 0.458,0.198 10 *a 2.396,1.448 2.854,1.646 0.458,0.198 10 E2
*a Front view of wire harness connector
(to Heater Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-2 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT HEATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT HEATER PUMP ASSEMBLY
a.

Remove the heater pump assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL


b.
E267500N01
2.438,1.625 2.198,1.625 2.198,1.625 1.896,1.219 false 0.948,1.615 1.146,1.615 1.146,1.615 1.573,1.208 false 2.5,1.552 2.813,1.75 0.313,0.198 10 B2 0.688,1.531 1,1.729 0.313,0.198 10 E2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (B2) - 2 (E2) Always 9 to 12 Ω



c.

Inspect heater pump assembly operation.

i.

Connect a positive (+) lead from the battery to terminal 1 (B2) and a negative (-) lead to terminal 2 (E2), and check the pressure of the hose by hand.

NOTICE:

This inspection must be done quickly (within 10 seconds) to prevent damage to the heater pump assembly.


OK:

The pressure is applied to the hose.




Result:
Proceed to
OK
NG



OK

NG