Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM3090E _54 Brake _008771 PARKING BRAKE _0049453 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.APPLY HIGH TEMPERATURE GREASE

a.
C278503C01
1.521,1.896 1.521,1.792 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the backing plate that contact the shoes.


Hide 47612 2.INSTALL PARKING BRAKE SHOE LEVER LH

Hide 46590 3.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Connect the parking brake cable to the parking brake shoe lever.


b.
C278504C01
1.854,0.625 1.781,0.74 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the following contact surfaces of the No. 2 parking brake shoe.

·

Shoe to anchor pin

·

Shoe to parking brake lever pin

·

Shoe to spring



c.
C278499

Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.


Hide 46580 4.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.
C278505C01
1.76,1.656 1.823,1.552 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the following contact surfaces of the No. 1 parking brake shoe.

·

Shoe to anchor pin

·

Shoe to spring



b.
C278498

Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.


Hide 47406A 5.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C278506C01
2.344,1.906 2.521,1.854 false
V100144

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the shoe adjusting screw set shown in the illustration.


b.

Install the shoe adjusting screw set.


Hide 46550G 6.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.

Using needle-nose pliers, install the shoe return tension spring.


Hide 47614 7.INSTALL PARKING BRAKE SHOE STRUT LH

a.
C278507C01
2.26,0.854 2.313,0.771 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the contact surface of the parking brake shoe strut and shoe return tension spring.


b.

Install the parking brake shoe strut.


Hide 46550E 8.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)

a.
C278497

Using needle-nose pliers, install the 2 shoe return tension springs.


Hide 9.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C278508C03
0.396,0.115 0.771,0.354 0.375,0.24 12 *A 4.26,0.115 4.635,0.354 0.375,0.24 12 *B
*A for LH Side *B for RH Side
V100135

Front - -


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining and disc.



Hide 42431 10.INSTALL REAR DISC

Hide 11.CHECK PARKING BRAKE LEVER TRAVEL

Hide 12.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 42491 13.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 14.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 15. SETTLE PARKING BRAKE SHOE AND DISC

a.

Pull the parking brake lever with a force of 147 N (15 kgf, 33 lbf).


b.

Drive the vehicle at approximately 50 km/h (31 mph) for approximately 400 m (0.25 miles).

NOTICE:

Drive the vehicle on a safe, level and dry road.



c.

Repeat the above steps 2 or 3 times.