Home › Engine / Hybrid System › 2AR-FE COOLING › COOLING FAN SYSTEM
RM3090E _51 Engine / Hybrid System _008400 2AR-FE COOLING _0046901 COOLING FAN SYSTEM J

2AR-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning switch (on/off), air conditioning refrigerant pressure, engine speed and vehicle speed signals.

The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Control the Electric Cooling Fan)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.


e.

Check the operation of the cooling fan while operating it using the GTS.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Electric Cooling Fan
50004 61 16
OK:
GTS Operation Fan Operation
ON Cooling fans operate
OFF Cooling fans stop



Result:
Result Proceed to
OK A
NG B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (FANL AND FANH VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (FANL AND FANH VOLTAGE)
a.

Disconnect the A62 ECM connector.


b.

Turn the ignition switch to ON.


c.
A255690C40
0.198,1.063 0.688,1.354 0.49,0.292 1.875,1.125 1.99,0.156 1.99,0.156 2.156,0.156 true 1.979,1.125 1.844,2 1.844,2 1.677,2 true 0.135,0.104 0.302,0.281 0.167,0.177 10 false *a 0.292,1.135 0.635,1.333 0.344,0.198 10 false A62 2.198,0.083 2.594,0.313 0.396,0.229 10 false FANL 1.292,1.917 1.708,2.083 0.417,0.167 10 false FANH
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-6 (FANH) - Body ground Ignition switch ON 11 to 14 V
A62-5 (FANL) - Body ground Ignition switch ON 11 to 14 V



d.

Reconnect the A62 ECM connector.


Result:
Result
OK
NG



OK

3.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)

NG

14.INSPECT FAN NO. 1 RELAY
3.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)
a.
A297235C01
0.094,0.083 0.406,0.24 0.313,0.156 10 *1 2.229,2.938 2.542,3.094 0.313,0.156 10 *2 2.208,1.469 2.521,1.625 0.313,0.156 10 *3
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 FAN NO. 1 Relay
*3 FAN NO. 3 Relay


Remove the FAN NO. 1 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V
3 (FAN NO. 3 relay) - Body ground Always 11 to 14 V



c.

Reinstall the FAN NO. 1 relay and FAN NO. 3 relay.


Result:
Result
OK
NG



OK

4.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FAN NO. 1 RELAY
a.

Result:
Result
OK
NG



OK

5.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

5.INSPECT FAN NO. 2 RELAY
a.

Result:
Result
OK
NG



OK

6.INSPECT FAN NO. 3 RELAY

NG

REPLACE FAN NO. 2 RELAY

6.INSPECT FAN NO. 3 RELAY
a.

Result:
Result
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

NG

REPLACE FAN NO. 3 RELAY

7.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.

Remove the FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (FAN NO. 2 relay) - Body ground Always Below 1 Ω



c.

Reinstall the FAN NO. 2 relay.


Result:
Result
OK
NG



OK

8.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT COOLING FAN MOTOR

Result:
Result
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPLACE COOLING FAN MOTOR

9.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A55 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-1 - Body ground Always Below 1 Ω



c.

Reconnect the A55 cooling fan motor connector.


Result:
Result
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A55 cooling fan motor connector.


b.

Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-2 - 5 (FAN NO. 1 relay) Always Below 1 Ω
A55-2 - 4 (FAN NO. 2 relay) Always Below 1 Ω
A55-2 or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher
A55-2 or 4 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reinstall the FAN NO. 1 relay and FAN NO. 2 relay.


e.

Reconnect the cooling fan motor connector.


Result:
Result
OK
NG



OK

11.INSPECT NO. 2 COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT NO. 2 COOLING FAN MOTOR
a.

Result:
Result
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

REPLACE NO. 2 COOLING FAN MOTOR

12.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A53 No. 2 cooling fan motor connector.


b.

Remove the FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A53-1 - 3 (FAN NO. 2 relay) Always Below 1 Ω
A53-2 - 5 (FAN NO. 3 relay) Always Below 1 Ω
A53-1 or 3 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
A53-2 or 5 (FAN NO. 3 relay) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reinstall the FAN NO. 2 relay and FAN NO. 3 relay.


e.

Reconnect the A53 No. 2 cooling fan motor connector.


Result:
Result
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)
a.

Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - 1 (FAN NO. 2 relay) Always Below 1 Ω
2 (FAN NO. 1 relay) - 2 (FAN NO. 2 relay) Always Below 1 Ω
1 (FAN NO. 1 relay) or 1 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
2 (FAN NO. 1 relay) or 2 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



c.

Reinstall the FAN NO. 1 relay and FAN NO. 2 relay.


Result:
Result
OK
NG



OK

REPLACE ECM

NG

REPLACE NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY

14.INSPECT FAN NO. 1 RELAY
a.

Result:
Result
OK
NG



OK

15.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

15.INSPECT FAN NO. 2 RELAY
a.

Result:
Result
OK
NG



OK

16.INSPECT FAN NO. 3 RELAY

NG

REPLACE FAN NO. 2 RELAY

16.INSPECT FAN NO. 3 RELAY
a.

Result:
Result
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPLACE FAN NO. 3 RELAY

17.CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)
a.

Remove the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) - A62-6 (FANH) Always Below 1 Ω
2 (FAN NO. 2 relay) - A62-6 (FANH) Always Below 1 Ω
2 (FAN NO. 3 relay) - A62-5 (FANL) Always Below 1 Ω
2 (FAN NO. 1 relay) or A62-6 (FANH) - Body ground Always 10 kΩ or higher
2 (FAN NO. 2 relay) or A62-6 (FANH) - Body ground Always 10 kΩ or higher
2 (FAN NO. 3 relay) or A62-5 (FANL) - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the A62 ECM connector.


e.

Reinstall the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.


Result:
Result
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)