Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049519 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·
B276679C03
0.621,1.754 0.818,1.944 0.197,0.19 10 *1 2.535,1.754 2.732,1.944 0.197,0.19 10 *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67005 1.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas A to E are within the standard ranges.

B336853E01
0.917,0.24 1.073,0.438 0.156,0.198 10 A 1.469,0.542 1.625,0.74 0.156,0.198 10 B 3.396,0.24 3.552,0.438 0.156,0.198 10 C 3.938,0.458 4.094,0.656 0.156,0.198 10 D 6.49,1.042 6.646,1.24 0.156,0.198 10 E 6.667,2.51 6.823,2.708 0.156,0.198 10 F 6.708,3.938 6.865,4.135 0.156,0.198 10 G

Standard Clearance
Area Measurement Area Measurement
A 6.0 to 9.0 mm (0.236 to 0.354 in.) B -0.5 to 2.5 mm (0.0196 to 0.0984 in.)
C 6.0 to 9.0 mm (0.236 to 0.354 in.) D -0.5 to 2.5 mm (0.0196 to 0.0984 in.)
E
(Reference)
3.35 to 7.35 mm (0.132 to 0.290 in.) F
(Reference)
3.5 to 7.5 mm (0.138 to 0.295 in.)
G 3.7 to 6.7 mm (0.147 to 0.264 in.) - -


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire, for Compact Spare Tire)

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY (w/ Full Size Spare Tire)

Hide 64997 4.REMOVE DECK FLOOR BOX LH

Hide 58386 5.REMOVE REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

Hide 64716P 6.REMOVE REAR DECK TRIM COVER (w/ Full Size Spare Tire)

Hide 67005 7.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B336854

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
B336855

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


d.

Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 64716P 8.INSTALL REAR DECK TRIM COVER (w/ Full Size Spare Tire)

Hide 58386 9.INSTALL REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

Hide 64997 10.INSTALL DECK FLOOR BOX LH

Hide 58410B 11.INSTALL DECK BOARD ASSEMBLY