Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3090E _55 Steering _008773 STEERING COLUMN _0049531 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 45020A 1.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

a.

Secure the steering column assembly in a vise.


b.

Using a center punch, mark the center of the tapered-head bolts.


c.

Using a 3 to 4 mm (0.12 to 0.16 in.) diameter drill bit, drill a hole in the tapered-head bolt.


d.
C275627C01
0.667,0.771 1.302,1.313 true 0.49,0.656 0.802,0.813 0.313,0.156 10 false *1
*1 Screw Extractor


Using a screw extractor, remove the 2 tapered-head bolts, and then remove the steering lock actuator assembly from the steering column assembly.


Hide 45020A 2.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/o Entry and Start System)

HINT:

Refer to "REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)"


Hide 89782 3.REMOVE TRANSPONDER KEY COIL (w/o Entry and Start System)

Hide 84450 4.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

Hide 85432 5.REMOVE KEY INTERLOCK SOLENOID (for Automatic Transaxle and CVT)

a.
C280247

Remove the screw and key lock solenoid from the upper steering column bracket assembly.


Hide 84052 6.REMOVE UNLOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C232527

Insert the key.


b.

Remove the unlock warning switch assembly by releasing the 2 claws.

HINT:

Slide the unlock warning switch assembly in the direction shown by the arrow in the illustration to remove it.



Hide 7.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.

Turn the ignition switch to ACC.


b.
C280245C01
0.427,2.604 0.635,2.031 true 0.344,2.635 0.188,1.938 true 1.458,1.99 1.771,2.188 0.313,0.198 10 false *b 1.469,0.531 1.781,0.729 0.313,0.198 10 false *a 0.052,1.729 0.365,1.927 0.313,0.198 10 false *1 0.625,1.875 0.938,2.073 0.313,0.198 10 false *2
*1 Claw
*2 Stopper
*a Push
*b Pull


Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly as shown in the illustration, and pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the upper steering column bracket assembly.

NOTICE:

Pull the ignition switch lock cylinder assembly out until the claw comes into contact with the stopper of the upper steering column bracket assembly. Otherwise, the following procedure cannot be conducted properly.



c.
C280246C01
0.188,1.427 0.51,0.646 true 2.188,0.542 2.219,0.333 true 1.417,1.26 1.49,1.031 true 0.51,0.542 0.469,0.313 true 0.344,0.583 0.24,0.365 true 0.333,0.177 0.646,0.375 0.313,0.198 10 false *1 0.094,0.229 0.406,0.427 0.313,0.198 10 false *2 2.135,0.167 2.448,0.365 0.313,0.198 10 false *a 0.063,1.417 0.375,1.615 0.313,0.198 10 false *b 1.646,1.573 1.958,1.771 0.313,0.198 10 false *c 1.719,3.177 2.031,3.375 0.313,0.198 10 false *d
*1 Claw
*2 Stopper
*a Claw detached
*b Driver Insertion Hole
*c Tilt
*d Pull out


Insert the tip of a screwdriver into the hole in the steering column bracket and tilt it downward as shown in the illustration to detach the claw on the ignition switch lock cylinder assembly. Then pull out the ignition switch lock cylinder assembly.


Hide 89650 8.REMOVE POWER STEERING ECU ASSEMBLY

Hide 80960 9.REMOVE POWER STEERING MOTOR ASSEMBLY

a.
C275628

Remove the 2 bolts and power steering motor assembly.


b.

Remove the O-ring from the power steering motor assembly.