Home › Steering › STEERING COLUMN › STEERING PAD SWITCH › 2012.12–2015.10
RM3090E _55 Steering _008773 STEERING COLUMN _0049532 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 84250A 1.INSPECT STEERING PAD SWITCH ASSEMBLY

a.

Inspect the pad switch.

i.

Measure the resistance according to the value(s) in the table below.

C275635
0.531,0.417 2.667,1.521 2.135,1.104 3.104,0.417 3.458,0.594 0.354,0.177 5.635,0.656 5.99,0.833 0.354,0.177 0.781,1.052 1.135,1.229 0.354,0.177 4.781,1.979 5.104,1.76 true 4.896,2.125 5.323,2.063 true 4.781,2.271 5.24,2.479 true 4.76,2.542 5.031,2.885 true 2.479,2.26 2.188,2.271 true 1.833,1.271 1.583,1.354 true 2.542,2.479 2.271,2.656 true 2.781,2.531 2.615,2.833 true 1.833,1.104 1.542,0.927 true 1.938,1.115 2.229,0.917 true 4.885,0.635 4.594,0.458 true 4.979,0.635 4.74,0.302 true 5.094,0.833 4.979,1.26 true 5.281,0.625 5.427,0.188 true 5.375,0.635 5.604,0.427 true 4.896,0.823 4.646,0.979 true 4.99,0.823 4.802,1.115 true 5.25,1.26 5.198,0.823 true 5.281,0.833 5.427,1.125 true 5.667,1.01 5.375,0.833 true 2.5,2.052 2.208,1.969 true 2.656,2.094 2.552,1.781 2.552,1.781 2.438,1.781 true 2.771,1.99 2.719,1.594 2.719,1.594 2.604,1.594 true 2.802,2.094 2.958,1.625 2.958,1.625 3.073,1.625 true 2.813,2.24 3.125,2.51 3.125,2.51 3.292,2.51 true 2.896,2.156 3.146,2.313 3.146,2.313 3.313,2.313 true 5.083,0.625 4.906,0.188 true 0.646,0.5 0.958,0.656 0.313,0.156 10 *A 2.063,1.854 2.375,2.01 0.313,0.156 10 *1 2.031,2.188 2.344,2.344 0.313,0.156 10 *2 2.281,1.708 2.594,1.865 0.313,0.156 10 *3 3.365,2.229 3.677,2.385 0.313,0.156 10 *4 2.469,1.521 2.781,1.677 0.313,0.156 10 *5 3.323,2.438 3.635,2.594 0.313,0.156 10 *6 3.115,1.542 3.427,1.698 0.313,0.156 10 *7 2.094,2.625 2.406,2.781 0.313,0.156 10 *8 2.49,2.875 2.802,3.031 0.313,0.156 10 *9 5.333,1.969 5.802,2.125 0.469,0.156 10 *10 5.115,1.646 5.583,1.802 0.469,0.156 10 *11 5.292,2.438 5.76,2.594 0.469,0.156 10 *12 5.042,2.906 5.51,3.063 0.469,0.156 10 *13 0.229,0.219 0.542,0.375 0.313,0.156 10 *a 4.375,0.365 4.688,0.563 0.313,0.198 10 HO 4.479,0.177 4.792,0.375 0.313,0.198 10 +DP 4.698,0.031 5.01,0.229 0.313,0.198 10 -DP 5.427,0.042 5.74,0.24 0.313,0.198 10 IL+2 5.635,0.323 5.948,0.521 0.313,0.198 10 SUP 5.688,0.958 6,1.156 0.313,0.198 10 SDN 5.427,1.104 5.74,1.302 0.313,0.198 10 AU1 4.781,1.271 5.094,1.469 0.313,0.198 10 AU3 4.51,1.104 4.823,1.302 0.313,0.198 10 EAU 4.344,0.896 4.656,1.094 0.313,0.198 10 ECC 2.25,0.813 2.563,1.01 0.313,0.198 10 SUP 1.25,0.823 1.563,1.021 0.313,0.198 10 SDN 1.281,1.302 1.594,1.5 0.313,0.198 10 ECC 5.219,1.271 5.531,1.469 0.313,0.198 10 AU2 5.76,0.667 6.073,0.865 0.313,0.198 10 A 3.229,0.438 3.542,0.635 0.313,0.198 10 B 0.896,1.063 1.208,1.26 0.313,0.198 10 C 3.177,0.771 3.615,1.031 0.438,0.26 10 HO
*A w/ Shift Paddle Switch - -
*1 Volume+ Switch *2 Volume- Switch
*3 Left Switch *4 Right Switch
*5 Up Switch *6 Down Switch
*7 ENTER Switch *8 MODE Switch
*9 Back Switch *10 w/ Voice Switch
*11 Off Hook Switch *12 On Hook Switch
*13 DISP Switch - -
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A11 (AU1) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Volume+ is pushed 950 to 1050 Ω
Volume- is pushed 2954 to 3265 Ω
Up switch is pushed Below 2.5 Ω
Down switch is pushed 312 to 345 Ω
A9 (AU3) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Left switch is pushed 2954 to 3265 Ω
Right switch is pushed 950 to 1050 Ω
ENTER Switch is pushed Below 2.5 Ω
Back Switch is pushed 312 to 345 Ω
A10 (AU2) - A8 (EAU) No switch is pushed 95 to 105 kΩ
MODE switch is pushed Below 2.5 Ω
On Hook switch is pushed 312 to 345 Ω
Off Hook switch is pushed 950 to 1050 Ω
Voice switch is pushed 2954 to 3265 Ω
A2 (+DP) - A3 (-DP) DISP switch is pushed Below 2.5 Ω
A1 (HO) - B (HO) Always Below 2.5 Ω
A6 (SUP) - C2 (SUP) Always Below 2.5 Ω
A12 (SDN) - C3 (SDN) Always Below 2.5 Ω
A7 (ECC) - C7 (ECC) Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


ii.

Connect the battery positive (+) lead to terminal A5 (IL+2) and the negative (-) lead to terminal A8 (EAU) of the steering pad switch assembly connector.


iii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.



b.

Inspect the pad switch.

i.

Measure the resistance according to the value(s) in the table below.

C294310
1.125,0.729 2.729,1.521 1.604,0.792 1.313,1.073 1.583,1.24 0.271,0.167 2.844,0.625 3.115,0.792 0.271,0.167 5.677,0.635 5.948,0.802 0.271,0.167 5.271,0.833 5.521,1.083 true 2.396,2.771 2.646,2.521 true 2.198,2.125 2.573,2.125 true 2.302,2.427 2.677,2.26 true 2.375,1.802 2.667,1.99 true 4.979,2.75 4.75,2.542 true 5.125,2.521 4.792,2.271 true 2.823,2.083 2.698,1.729 true 5.271,0.625 5.5,0.375 true 4.625,0.458 4.885,0.625 true 4.635,1 4.885,0.833 true 5.646,1 5.396,0.833 true 5.625,0.458 5.375,0.625 true 5,0.833 4.75,1.083 true 5,0.615 4.75,0.365 true 5.188,0.844 5.354,1.177 true 4.906,0.281 5.073,0.615 true 1.833,0.927 2.021,1.094 true 1.833,1.406 2.021,1.281 true 2.292,0.917 2.125,1.104 true 5.156,1.729 4.76,2 true 1.396,1.083 1.552,1.281 0.156,0.198 10 false C 2.927,0.635 3.083,0.833 0.156,0.198 10 false B 5.76,0.635 5.917,0.833 0.156,0.198 10 false A 2.208,1.729 2.521,1.885 0.313,0.156 10 false *1 2.125,2.365 2.438,2.521 0.313,0.156 10 false *2 2.583,1.563 2.896,1.719 0.313,0.156 10 false *3 2.021,2.052 2.333,2.208 0.313,0.156 10 false *4 2.208,2.771 2.521,2.927 0.313,0.156 10 false *5 5.021,2.781 5.333,2.938 0.313,0.156 10 false *6 5.188,1.635 5.5,1.792 0.313,0.156 10 false *7 5.188,2.469 5.5,2.625 0.313,0.156 10 false *8 0.125,0.146 0.438,0.302 0.313,0.156 10 false *a 1.188,0.771 1.344,0.927 0.156,0.156 10 false *A 1.542,0.802 2,1 0.458,0.198 10 false SDN 2.323,0.802 2.781,1 0.458,0.198 10 false SUP 1.542,1.354 2,1.552 0.458,0.198 10 false ECC 4.365,0.365 4.729,0.563 0.365,0.198 10 false Il+2 5.667,0.385 6.031,0.583 0.365,0.198 10 false SUP 5.677,0.938 6.042,1.135 0.365,0.198 10 false SDN 5.51,1.083 5.875,1.281 0.365,0.198 10 false AU1 5.24,1.198 5.604,1.396 0.365,0.198 10 false AU2 4.448,1.083 4.813,1.281 0.365,0.198 10 false EAU 4.344,0.917 4.708,1.115 0.365,0.198 10 false ECC 5.521,0.219 5.885,0.417 0.365,0.198 10 false HO 4.51,0.208 4.875,0.406 0.365,0.198 10 false +DP 4.813,0.115 5.177,0.313 0.365,0.198 10 false -DP 3.188,0.792 3.552,0.99 0.365,0.198 10 false HO
*A w/ Shift Paddle Switch - -
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 DISP Switch
*7 w/ Off Hook Switch *8 w/ On Hook Switch
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A11 (AU1) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Volume+ is pushed 950 to 1050 Ω
Volume- is pushed 2954 to 3265 Ω
Seek+ switch is pushed Below 2.5 Ω
Seek- switch is pushed 312 to 345 Ω
A10 (AU2) - A8 (EAU) No switch is pushed 95 to 105 kΩ
MODE switch is pushed Below 2.5 Ω
On Hook switch is pushed 312 to 345 Ω
Off Hook switch is pushed 950 to 1050 Ω
A2 (+DP) - A3 (-DP) DISP switch is pushed Below 2.5 Ω
A5 (HO) - B (HO) Always Below 2.5 Ω
A6 (SUP) - C2 (SUP) Always Below 2.5 Ω
A12 (SDN) - C3 (SDN) Always Below 2.5 Ω
A7 (ECC) - C7 (ECC) Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


ii.

Connect the battery positive (+) lead to terminal A1 (IL+2) and the negative (-) lead to terminal A8 (EAU) of the steering pad switch assembly connector.


iii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.