Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 16 inch Front Brake)
RM3090E _54 Brake _008769 BRAKE (FRONT) _0049552 FRONT BRAKE(for 16 inch Front Brake) A

BRAKE (FRONT)  FRONT BRAKE(for 16 inch Front Brake)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C127063
2.417,0.091 2.569,0.240 0.152,0.149 10 *a 1.761,1.049 1.761,0.177 1.761,0.177 2.395,0.177 false 1.782,1.164 1.963,1.164 1.963,1.164 1.963,0.177 false
*a Matchmark


Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 2.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C193393
0.767,4.149 0.927,4.31 0.159,0.161 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire circumference of a new front disc brake bush dust boot, and the entire inner circumference of both ends.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the front disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the front disc brake bush dust boot and front disc brake cylinder mounting contact surfaces.



b.

Install the 2 boots to the mounting.


Hide 47769 3.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C187987
0.72,1.695 0.899,1.845 0.179,0.149 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin where it contacts the front disc brake cylinder slide bush.


b.

Install a new front disc brake cylinder slide bush to the No. 2 front disc brake cylinder slide pin.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C217115
0.743,2.915 0.938,3.064 0.196,0.149 10 *3 1.922,0.128 2.094,0.282 0.172,0.154 10 *1 0.53,2.289 0.702,2.459 0.172,0.17 10 *2 1.134,1.906 0.624,1.906 0.624,1.906 0.624,2.274 false 1.459,0.57 1.459,0.215 1.459,0.215 1.91,0.215 false
*1 Front Disc Brake Cylinder Slide Pin
*2 No. 2 Front Disc Brake Cylinder Slide Pin
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the 2 front disc brake cylinder slide pins.


b.

Install the front disc brake cylinder slide pin to the mounting.


Hide 47715D 5.INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN

a.

Install the No. 2 front disc brake cylinder slide pin to the mounting.


Hide 47722 6.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.

Install the cylinder mounting with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 7.INSTALL NO. 1 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 No. 1 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 8.INSTALL NO. 2 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 No. 2 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 9.INSTALL NO. 1 PAD WEAR INDICATOR PLATE

a.

Install the 2 pad wear indicator plates to the pads.


Hide 04945 10.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C127978
0.679,2.239 0.833,2.384 0.154,0.145 10 *2 2.877,1.313 3.038,1.453 0.161,0.14 10 *2 0.767,0.133 0.923,0.279 0.156,0.146 10 *3 2.494,3.07 2.645,3.211 0.151,0.14 10 *4 0.463,0.683 0.463,0.214 0.463,0.214 0.749,0.214 false 2.581,0.602 2.738,0.748 0.156,0.146 10 *1 0.768,1.642 0.768,2.233 false 1.391,1.188 1.391,0.686 1.391,0.686 2.566,0.686 false 2.104,1.59 2.104,0.69 false 2.59,1.919 2.59,1.395 2.59,1.395 2.871,1.395 false 2.997,2.919 2.997,3.145 2.997,3.145 2.667,3.145 false
*1 Front Disc Brake Pad
*2 No. 1 Anti-squeal Shim
*3 No. 2 Anti-squeal Shim (Inner)
*4 No. 2 Anti-squeal Shim (Outer)


Install the No. 1 and No. 2 shims to the pads.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and direction as shown in the illustration.




Hide 04465 11.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 disc brake pads to the mounting.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the pads and disc.



Hide 47750 12.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C265924
2.811,2.284 2.963,2.430 0.152,0.146 10 *a 2.627,3.132 2.779,3.277 0.152,0.145 10 *b 2.338,2.564 2.653,2.372 2.653,2.372 2.8,2.372 false 1.869,2.665 2.476,3.221 2.476,3.221 2.613,3.221 false
*a Hold
*b Turn


Hold the front disc brake cylinder slide pins and install the disc brake cylinder to the disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313A 13.CONNECT FRONT FLEXIBLE HOSE

a.
C127057

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the cylinder.



Hide 55784D 14.REMOVE COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 15.BLEED BRAKE LINE

Hide 55784D 16.INSTALL COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 17.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)