Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 17 inch Front Disc Brake)
RM3090E _54 Brake _008769 BRAKE (FRONT) _0049556 FRONT BRAKE(for 17 inch Front Disc Brake) A

BRAKE (FRONT)  FRONT BRAKE(for 17 inch Front Disc Brake)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C278598
2.01,1.052 2.01,0.167 2.01,0.167 2.74,0.167 false 2.031,1.094 2.375,1.094 2.375,1.094 2.375,0.177 false 2.813,0.073 3.01,0.281 0.198,0.208 10 *a
*a Matchmark


Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 2.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C193393
0.767,4.149 0.927,4.31 0.159,0.161 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots as shown in the illustration.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the front disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the front disc brake bush dust boot and front disc brake cylinder mounting contact surfaces.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47769 3.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C187987
0.72,1.695 0.899,1.845 0.179,0.149 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the contact surface of a new front disc brake cylinder slide bushing and the No. 2 front disc brake cylinder slide pin.


b.

Install the front disc brake cylinder slide bushing to the No. 2 front disc brake cylinder slide pin.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C217115
0.743,2.915 0.938,3.064 0.196,0.149 10 *3 1.922,0.128 2.094,0.282 0.172,0.154 10 *1 0.53,2.289 0.702,2.459 0.172,0.17 10 *2 1.134,1.906 0.624,1.906 0.624,1.906 0.624,2.274 false 1.459,0.57 1.459,0.215 1.459,0.215 1.91,0.215 false
*1 Front Disc Brake Cylinder Slide Pin
*2 No. 2 Front Disc Brake Cylinder Slide Pin
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the front disc brake cylinder slide pins as shown in the illustration.


b.

Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to align them.


Hide 47715D 5.INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN

a.

Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 front disc brake cylinder slide pin.


b.

Install the No. 2 front disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the No. 2 front disc brake cylinder slide pin into the front disc brake bushing dust boot to align them.


Hide 47722 6.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.

Install the cylinder mounting with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 7.INSTALL NO. 1 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the No. 1 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 8.INSTALL NO. 2 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the No. 2 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 9.INSTALL NO. 3 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the No. 3 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 10.INSTALL NO. 4 FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the No. 4 front disc brake pad support plates to the disc brake cylinder mounting.


Hide 11.INSTALL NO. 1 PAD WEAR INDICATOR PLATE

a.

Install the 2 pad wear indicator plates to the pads.


Hide 04945 12.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C279246
1.469,0.781 1.469,0.573 1.469,0.573 2.385,0.573 false 2.146,1.156 2.146,0.573 false 2.365,2.74 1.927,2.74 false 0.771,1.583 0.771,2.031 false 2.865,3.031 2.531,3.031 false 0.292,1.302 0.292,1.708 false 2.458,0.51 2.646,0.677 0.188,0.167 10 false *1 0.708,2.073 0.875,2.26 0.167,0.188 10 false *2 1.719,2.677 1.885,2.865 0.167,0.188 10 false *2 2.333,2.99 2.5,3.177 0.167,0.188 10 false *3 0.229,1.76 0.396,1.948 0.167,0.188 10 false *3
*1 Front Disc Brake Pad
*2 No. 1 Front Anti-squeal Shim
*3 No. 2 Front Anti-squeal Shim


Apply disc brake grease between the front disc brake pads.


b.

Install the 2 No.1 anti-squeal shims and No. 2 anti-squeal shims to the front disc brake pads.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and direction.




Hide 04465 13.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the pads and disc.



Hide 47750 14.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C279250
2.604,2.26 2.896,2.063 2.896,2.063 3.031,2.063 false 1.979,2.104 2.396,3.063 2.396,3.063 2.583,3.063 false 3.083,1.99 3.271,2.188 0.188,0.198 10 *a 2.615,2.99 2.844,3.177 0.229,0.188 10 *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pins and install the disc brake cylinder to the front disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 47313A 15.CONNECT FRONT FLEXIBLE HOSE

a.

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:

Insert the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 55784D 16.REMOVE COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 17.BLEED BRAKE LINE

Hide 55784D 18.INSTALL COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 19.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)