Home › Power Source / Network › 2AD-FHV BATTERY / CHARGING › GENERATOR
RM3090E _57 Power Source / Network _008778 2AD-FHV BATTERY / CHARGING _0049601 GENERATOR A

2AD-FHV BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A196742N01
2.783,0.494 3.092,0.655 0.309,0.161 10 SST 1.974,1.133 2.44,1.133 2.44,1.133 2.44,0.596 false 1.866,0.596 2.754,0.596 false

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A196745

Place the generator drive end frame assembly on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame assembly.


c.
A196739C02
1.958,0.458 2.229,0.167 2.229,0.167 2.448,0.167 false 2.458,0.052 2.771,0.25 0.313,0.198 10 *1
*1 New Washer


Place a new washer on the generator rotor assembly.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A196746C02
1.833,0.708 2.271,0.438 2.271,0.438 2.594,0.438 true 2.615,0.292 3.073,0.521 0.458,0.229 10 *1
*1 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


b.

Install the generator coil assembly with the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A158992C16
1.021,0.708 1.448,0.177 1.448,0.177 1.604,0.177 false 1.646,0.104 1.958,0.26 0.313,0.156 10 *1
*1 Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A196747C02
0.786,0.339 0.958,0.492 0.171,0.153 10 *1 0.976,0.423 1.133,0.423 1.133,0.423 1.71,1.195 false
*1 Pin


Install the generator brush holder assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 5.INSTALL GENERATOR TERMINAL INSULATOR

a.

Install the generator terminal insulator to the generator coil assembly.


Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley with clutch.


b.

Mount the generator in a vise between aluminum plates.


c.
A196749C03
1.49,1.333 1.625,1.333 1.625,1.333 1.729,0.875 true 1.948,0.156 2.083,0.156 2.083,0.156 1.917,0.573 false 0.813,0.24 0.948,0.24 0.948,0.24 1.073,0.542 false 0.938,1.26 1.469,1.458 0.531,0.198 10 SST (A) 1.302,0.063 1.833,0.26 0.531,0.198 10 SST (B) 0.646,0.135 0.958,0.292 0.313,0.156 10 *1
*1 Generator Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely install SST to the generator pulley with clutch and generator rotor shaft.



d.
A196750C03
0.896,0.385 1.094,0.385 1.094,0.385 1.417,0.75 false 0.75,1.104 0.906,1.104 0.906,1.104 1.177,1.031 false 0.24,0.292 0.792,0.479 0.552,0.188 10 SST (B) 0.094,1 0.646,1.188 0.552,0.188 10 SST (A) 1.385,2.052 1.542,2.208 0.156,0.156 10 *a 0.917,2.49 1.094,2.656 0.177,0.167 10 *1
*1 Fulcrum Length
*a Hold
V100135

Turn


Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

Torque:
without SST : 111 N*m (1127 kgf*cm, 81 ft.*lbf)
with SST : 88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

Make sure SST and the wrench are connected in a straight line.




e.

Check that the generator pulley rotates smoothly.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.
A196751

Install a new generator pulley cap.