Home › Power Source / Network › 1AD-FTV BATTERY / CHARGING › GENERATOR › 2012.12–2015.10
RM3090E _57 Power Source / Network _008779 1AD-FTV BATTERY / CHARGING _0049700 GENERATOR A

1AD-FTV BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A196731

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in a vise between aluminum plates.


b.
A297142
1.583,0.583 1.5,0.167 1.5,0.167 1.667,0.167 false 1.75,0.917 2,1.583 2,1.583 2.167,1.583 true 2,1.583 2.833,0.833 true 2.25,0.583 2.563,0.74 0.313,0.156 10 false *1 2.198,1.51 2.969,1.708 0.771,0.198 10 false SST (A) 1.698,0.094 2.469,0.292 0.771,0.198 10 false SST (B)
*1 Generator Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



c.
A297143
2.344,0.813 2.677,0.813 true 2.083,0.542 2.25,0.292 2.25,0.292 2.417,0.292 true 1.969,1.823 2.281,1.979 0.313,0.156 10 false *a 2.708,0.75 3.219,0.948 0.51,0.198 10 false SST (A) 2.448,0.208 3.219,0.406 0.771,0.198 10 false SST (B)
*a Hold
V100135

Turn


Using a wrench to hold SST (A), turn SST (B) counterclockwise to loosen the generator pulley with clutch.

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



d.

Remove SST from the generator assembly.


e.

Remove the generator pulley with clutch from the generator rotor shaft.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A297144

Place the generator assembly on the generator pulley with clutch.


b.

Remove the 3 nuts and generator rear end cover.


Hide 27387 4.REMOVE TERMINAL INSULATOR

a.
A297145

Remove the terminal insulator.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A297146

Remove the 2 screws and generator brush holder assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A297147

Remove the 4 bolts.


b.
A196738
1.125,2.646 1.01,2.646 1.01,2.646 0.646,2.427 true 2.385,2.656 2.49,2.656 2.49,2.656 2.927,2.406 true 1.125,0.604 1.323,0.604 1.323,0.604 1.625,1.021 false 0.198,1.385 0.385,1.552 0.188,0.167 10 *a 0.76,0.51 1.073,0.656 0.313,0.146 10 SST 1.156,2.563 1.469,2.708 0.313,0.146 10 SST 2.073,2.594 2.385,2.74 0.313,0.146 10 SST
*a Hold
V100135

Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A196812
2.74,0.208 2.604,0.208 2.604,0.208 1.969,0.469 true 2.74,0.813 2.396,0.813 false 2.74,0.115 2.896,0.271 0.156,0.156 10 *1 2.76,0.719 2.938,0.875 0.177,0.156 10 *2
*1 Washer
*2 Generator Rotor Assembly


Remove the washer and generator rotor assembly.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A196743

Check that the generator drive end frame bearing is not rough or worn, and that it rotates smoothly.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A196740

Remove the 4 screws and retainer plate.


b.
A196741
2.611,1.032 2.92,1.171 0.309,0.139 10 SST 2.584,1.118 1.773,1.118 false 1.771,1.485 2.49,1.485 2.49,1.485 2.49,1.118 false 1.771,1.485 2.49,1.485 false

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)