Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  U0101  Lost Communication with TCM  


DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).

If there is a problem with this communication, the ECM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0101 Lost Communication with TCM The following conditions are met for 1.25 seconds (1 trip detection logic):
·

The battery voltage is 10.5 V or higher.

·

No communication between the ECM and TCM.


·

ECM

·

TCM

·

ECM to TCM circuit


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U0101 Ignition switch ON for 3 seconds

WIRING DIAGRAM

C206826E07
0.313,1 2.406,1.25 2.094,0.25 10 from EFI MAIN NO. 1 Relay 5.813,3.271 6.208,3.469 0.396,0.198 10 TCM 5.813,3.083 6.26,3.281 0.448,0.198 10 B79 5.625,2.573 5.865,2.771 0.24,0.198 10 E1 5.625,1 6.063,1.198 0.438,0.198 10 +B 5.354,1.125 5.573,1.323 0.219,0.198 10 18 5.438,2.698 5.635,2.896 0.198,0.198 10 8 5.625,1.521 6.063,1.719 0.438,0.198 10 CAN+ 5.438,1.646 5.656,1.844 0.219,0.198 10 6 5.625,2.042 6.063,2.24 0.438,0.198 10 CAN- 5.438,2.177 5.656,2.375 0.219,0.198 10 7 3.135,1.521 3.573,1.719 0.438,0.198 10 CAN+ 3.615,1.646 3.833,1.844 0.219,0.198 10 40 3.135,2.042 3.573,2.24 0.438,0.198 10 CAN- 3.615,2.177 3.833,2.375 0.219,0.198 10 63 3.01,2.635 3.406,2.833 0.396,0.198 10 ECM 3.01,2.458 3.458,2.656 0.448,0.198 10 B76

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC U0101 is output
DTC U0101 and other DTCs are output


HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




DTC U0101 is output

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)

DTC U0101 and other DTCs are output

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TCM)
a.
C205632C07
1.51,0.156 2.063,0.417 0.552,0.26 0.875,1.719 1.198,1.073 false 1.49,1.719 1.26,1.24 false 0.063,0 0.375,0.198 0.313,0.198 10 *1 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 0.573,1.76 1.052,1.958 0.479,0.198 10 8 (E1) 1.281,1.76 1.813,1.958 0.531,0.198 10 18 (+B)
*1 Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B79-18 (+B) - B79-8 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.
C206298C01
1.51,2.531 1.969,2.792 0.458,0.26 1.51,0.323 1.948,0.583 0.438,0.26 2.521,4.094 2.167,3.417 false 1.708,4.094 2.063,3.417 false 2.271,1.906 1.865,1.083 false 1.49,1.906 1.865,1.156 false 0.052,2.219 0.333,2.417 0.281,0.198 10 false *2 1.573,2.573 1.948,2.802 0.375,0.229 10 false B79 2.271,4.135 2.917,4.333 0.646,0.198 10 false 7 (CAN-) 0.052,0.01 0.333,0.208 0.281,0.198 10 false *1 1.573,0.365 1.948,0.594 0.375,0.229 10 false B76 1.302,4.135 1.948,4.333 0.646,0.198 10 false 6 (CAN+) 2.01,1.927 2.708,2.125 0.698,0.198 10 false 40 (CAN+) 1,1.927 1.74,2.125 0.74,0.198 10 false 63 (CAN-)
*1 Front view of wire harness connector
(to ECM)
*2 Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-40 (CAN+) - B79-6 (CAN+) Always Below 1 Ω
B76-63 (CAN-) - B79-7 (CAN-) Always Below 1 Ω
B76-40 (CAN+) or B79-6 (CAN+) - Body ground Always 10 kΩ or higher
B76-63 (CAN-) or B79-7 (CAN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC U0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC is not output
DTC U0101 is output




DTC is not output

END

DTC U0101 is output

6.REPLACE TCM
6.REPLACE TCM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END