Home › Vehicle Interior › SEAT › FRONT SEAT CUSHION HEATER(for Manual Seat)
RM3090E _58 Vehicle Interior _008433 SEAT _0049772 FRONT SEAT CUSHION HEATER(for Manual Seat) G

SEAT  FRONT SEAT CUSHION HEATER(for Manual Seat)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87510L 1.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY LH

B341143
1.583,1.583 1.083,1.583 true 2.115,1.583 2.667,1.583 true 0.271,1.677 0.583,1.833 0.313,0.156 10 *a 0.521,2.083 0.833,2.24 0.313,0.156 10 *1 2,2.177 2.313,2.333 0.313,0.156 10 *2 2.688,1.5 3,1.656 0.313,0.156 10 *3 0.917,1.51 1.229,1.667 0.313,0.156 10 *3
*1 Connector A
*2 Connector B
*3 Thermostat
*a Component without harness connected
(Front Seat Cushion Heater Assembly LH)


a.

Check the front seat cushion heater assembly LH.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Seat cushion heater temperature 20°C (68°F) 3.25 to 3.31 Ω
A-2 - B-2 1.78 to 1.82 Ω
A-1 - B-1 Below 1 Ω


If the result is not as specified, replace the front seat cushion heater assembly LH.


ii.

Check the thermostat resistance.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Thermostat temperature 42°C (108°F) 10 kΩ or higher
A-2 - B-2 10 kΩ or higher


If the result is not as specified, replace the front seat cushion heater assembly LH.



Hide 87510K 2.INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH

B341143
1.583,1.583 1.083,1.583 true 2.115,1.583 2.667,1.583 true 0.271,1.677 0.583,1.833 0.313,0.156 10 *a 0.521,2.083 0.833,2.24 0.313,0.156 10 *1 2,2.177 2.313,2.333 0.313,0.156 10 *2 2.688,1.5 3,1.656 0.313,0.156 10 *3 0.917,1.51 1.229,1.667 0.313,0.156 10 *3
*1 Connector A
*2 Connector B
*3 Thermostat
*a Component without harness connected
(Front Seat Cushion Heater Assembly RH)


a.

Check the front seat cushion heater assembly RH.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Seat cushion heater temperature 20°C (68°F) 3.25 to 3.31 Ω
A-2 - B-2 1.78 to 1.82 Ω
A-1 - B-1 Below 1 Ω


If the result is not as specified, replace the front seat cushion heater assembly RH.


ii.

Check the thermostat resistance.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Thermostat temperature 42°C (108°F) 10 kΩ or higher
A-2 - B-2 10 kΩ or higher


If the result is not as specified, replace the front seat cushion heater assembly RH.