Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH
RM3090E _58 Vehicle Interior _008433 SEAT _0049770 SEAT HEATER SWITCH G

SEAT  SEAT HEATER SWITCH  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84751F 1.INSPECT SEAT HEATER SWITCH LH

B338636
1.594,2.573 1.188,2.042 true 1.844,2.573 2.313,2.021 true 1.708,3.156 1.708,2.833 true 1.26,3.125 1.594,2.833 true 1.719,2.573 1.719,2.021 true 1.844,2.823 2.135,3.104 true 0.26,1.708 0.573,1.865 0.313,0.156 10 *a 2.26,1.865 2.573,2.063 0.313,0.198 10 LO 1.688,1.854 2,2.052 0.313,0.198 10 IG 1.104,1.885 1.417,2.083 0.313,0.198 10 HI 2.094,3.135 2.708,3.333 0.615,0.198 10 ILL+ 1.625,3.135 2.24,3.333 0.615,0.198 10 ILL- 1.198,3.135 1.354,3.333 0.156,0.198 10 E
*a Component without harness connected
(Seat Heater Switch LH)


a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (IG) - 3 (HI) HI position on Below 1 Ω
1 (LO) - 6 (E) Below 1 Ω
2 (IG) - 1 (LO) LO position on Below 1 Ω


If the result is not as specified, replace the seat heater switch LH.



b.

Inspect the indicator operation.

i.

Apply battery voltage to the seat heater switch LH connector, and check that the seat heater switch LH indicator LED illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 2 (IG)
Battery negative (-) → 6 (E)
HI position on HI indicator LED illuminates
Battery positive (+) → 2 (IG)
Battery negative (-) → 6 (E)
LO position on LO indicator LED illuminates


If the result is not as specified, replace the seat heater switch LH.



c.

Inspect the illumination operation.

i.

Apply battery voltage to the seat heater switch LH connector, and check that the seat heater switch LH LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (ILL+)
Battery negative (-) → 5 (ILL-)
LED illuminates


If the result is not as specified, replace the seat heater switch LH.



Hide 84751F 2.INSPECT SEAT HEATER SWITCH RH

B338637
1.219,3.125 1.49,2.833 true 1.719,2.563 1.719,2.031 true 1.844,2.583 2.344,2.073 true 1.615,2.573 1.198,2.073 true 1.729,2.833 1.729,3.135 true 1.958,2.844 2.188,3.135 true 0.615,1.729 0.927,1.885 0.313,0.156 10 false *a 2.302,1.896 2.615,2.094 0.313,0.198 10 false LO 1.667,1.865 1.979,2.063 0.313,0.198 10 false IG 1.115,1.906 1.427,2.104 0.313,0.198 10 false HI 2.125,3.146 2.74,3.344 0.615,0.198 10 false ILL+ 1.656,3.146 2.271,3.344 0.615,0.198 10 false ILL- 1.146,3.156 1.302,3.354 0.156,0.198 10 false E
*a Component without harness connected
(Seat Heater Switch RH)


a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (IG) - 4 (HI) HI position on Below 1 Ω
2 (LO) - 10 (E) Below 1 Ω
3 (IG) - 2 (LO) LO position on Below 1 Ω


If the result is not as specified, replace the seat heater switch RH.



b.

Inspect the indicator operation.

i.

Apply battery voltage to the seat heater switch RH connector, and check that the seat heater switch RH indicator LED illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 3 (IG)
Battery negative (-) → 10 (E)
HI position on HI indicator LED illuminates
Battery positive (+) → 3 (IG)
Battery negative (-) → 10 (E)
LO position on LO indicator LED illuminates


If the result is not as specified, replace the seat heater switch RH.



c.

Inspect the illumination operation.

i.

Apply battery voltage to the seat heater switch RH connector, and check that the seat heater switch RH LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 8 (ILL-)
LED illuminates


If the result is not as specified, replace the seat heater switch RH.