Home › Vehicle Interior › SEAT › POWER SEAT SWITCH
RM3090E _58 Vehicle Interior _008433 SEAT _0049769 POWER SEAT SWITCH G

SEAT  POWER SEAT SWITCH  INSPECTION  


PROCEDURE

Hide 84922 1.INSPECT FRONT POWER SEAT SWITCH

B239569
1.875,3.115 1.99,2.615 false 2.573,3.656 2.156,3.375 false 2.031,3.125 2.448,2.708 false 2.385,3.76 2.01,3.365 false 2.323,1.104 2.813,0.615 false 2.063,3.875 1.885,3.375 false 1.521,3.115 1.385,2.604 false 1.198,3.802 1.615,3.385 false 1.281,1.344 0.969,0.396 false 0.427,1.365 0.917,1.365 false 1.219,3.167 0.865,3.167 false 0.979,3.729 1.479,3.375 false 1.385,3.115 1.073,2.75 false 1.542,3.875 1.75,3.385 false 1.646,1.354 2.063,0.385 false 2.156,3.167 2.542,3.167 false 0.833,0.281 1.146,0.438 0.313,0.156 10 *1 0.271,1.271 0.583,1.427 0.313,0.156 10 *2 2.063,0.229 2.375,0.385 0.313,0.156 10 *3 2.854,0.458 3.167,0.615 0.313,0.156 10 *4 0.323,2.313 0.635,2.469 0.313,0.156 10 *a 0.438,3.094 1.052,3.292 0.615,0.198 10 FDWN 0.74,2.615 1.354,2.813 0.615,0.198 10 SLDF 1.198,2.406 1.813,2.604 0.615,0.198 10 LDWN 1.865,2.396 2.323,2.594 0.458,0.198 10 LUP 2.458,2.563 3.073,2.76 0.615,0.198 10 SLDR 2.583,3.094 3.042,3.292 0.458,0.198 10 FUP 0.781,3.708 1.094,3.906 0.313,0.198 10 E1 1.115,3.823 1.271,4.021 0.156,0.198 10 E 1.438,3.896 2.052,4.094 0.615,0.198 10 RCLF 1.948,3.896 2.563,4.094 0.615,0.198 10 RCLR 2.438,3.781 2.594,3.979 0.156,0.198 10 B 2.635,3.625 2.948,3.823 0.313,0.198 10 B1
*1 Slide Switch
*2 Front Vertical Switch
*3 Lifter Switch
*4 Reclining Switch
*a Component without harness connected
(Front Power Seat Switch)


a.

Check the resistance of the slide switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (SLDF) - 8 (B)
5 (SLDF) - 7 (B1)
Front position Below 1 Ω
2 (SLDR) - 11 (E)
2 (SLDR) - 12 (E1)
5 (SLDF) - 11 (E)
5 (SLDF) - 12 (E1)
Neutral Below 1 Ω
2 (SLDR) - 11 (E)
2 (SLDR) - 12 (E1)
5 (SLDF) - 11 (E)
5 (SLDF) - 12 (E1)
Rear position Below 1 Ω
2 (SLDR) - 8 (B)
2 (SLDR) - 7 (B1)


If the result is not as specified, replace the front power seat switch.



b.

Check the resistance of the front vertical switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (FUP) - 8 (B)
1 (FUP) - 7 (B1)
Up position Below 1 Ω
6 (FDWN) - 11 (E)
6 (FDWN) - 12 (E1)
1 (FUP) - 11 (E)
1 (FUP) - 12 (E1)
Neutral Below 1 Ω
6 (FDWN) - 11 (E)
6 (FDWN) - 12 (E1)
1 (FUP) - 11 (E)
1 (FUP) - 12 (E1)
Down position Below 1 Ω
6 (FDWN) - 8 (B)
6 (FDWN) - 7 (B1)


If the result is not as specified, replace the front power seat switch.



c.

Check the resistance of the lifter switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (LUP) - 8 (B)
3 (LUP) - 7 (B1)
Up position Below 1 Ω
4 (LDWN) - 11 (E)
4 (LDWN) - 12 (E1)
3 (LUP) - 11 (E)
3 (LUP) - 12 (E1)
Neutral Below 1 Ω
4 (LDWN) - 11 (E)
4 (LDWN) - 12 (E1)
3 (LUP) - 11 (E)
3 (LUP) - 12 (E1)
Down position Below 1 Ω
4 (LDWN) - 8 (B)
4 (LDWN) - 7 (B1)


If the result is not as specified, replace the front power seat switch.



d.

Check the resistance of the reclining switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (RCLF) - 8 (B)
10 (RCLF) - 7 (B1)
10 (RCLF) - 1 (FUP)
10 (RCLF) - 6 (FDWN)
Front position Below 1 Ω
9 (RCLR) - 11 (E)
9 (RCLR) - 12 (E1)
10 (RCLF) - 11 (E)
10 (RCLF) - 12 (E1)
Neutral Below 1 Ω
9 (RCLR) - 11 (E)
9 (RCLR) - 12 (E1)
10 (RCLF) - 11 (E)
10 (RCLF) - 12 (E1)
Rear position Below 1 Ω
9 (RCLR) - 8 (B)
9 (RCLR) - 7 (B1)
9 (RCLR) - 1 (FUP)
9 (RCLR) - 6 (FDWN)


If the result is not as specified, replace the front power seat switch.