Home › Engine / Hybrid System › 2AD-FTV STARTING › STARTER
RM3090E _51 Engine / Hybrid System _008741 2AD-FTV STARTING _0049818 STARTER A

2AD-FTV STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A298954
1.917,0.854 1.917,0.844 false
V100135

High-temperature Grease


Apply high-temperature grease to the areas of the starter pinion drive lever indicated in the illustration.


b.

Install the starter pinion drive lever and rubber seal to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch sub-assembly together with the starter pinion drive lever and rubber seal to the starter drive housing assembly.


d.
A298955
1.5,1.396 1.51,1.396 false
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and pins of the starter center bearing clutch sub-assembly.


e.

Install the 3 planetary gears.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.



Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A215977

Push out the 4 brushes from the starter brush holder assembly so that they are held in place by the springs as shown in the illustration.


b.
A215968

Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes.

NOTICE:

Check that the positive (+) lead wires are not grounded.



c.
A187223
0.876,0.194 1.04,0.194 1.04,0.194 1.55,0.896 false 1.817,1.234 1.958,1.456 0.141,0.221 0.688,0.099 0.846,0.255 0.158,0.156 10 *1 0.585,0.528 0.754,0.683 0.168,0.155 10 *2 0.785,0.617 0.866,0.617 0.866,0.617 1.324,0.974 false 2.641,1.194 2.806,1.346 0.164,0.152 10 *3 2.624,1.287 2.516,1.287 2.516,1.287 2.1,0.944 false
*1 Grommet
*2 Negative Side
*3 Positive Side


Insert the grommet between the positive side and negative side.


Hide 4.INSTALL STARTER YOKE ASSEMBLY

a.
A290045
1.031,1.448 1.219,1.448 1.219,1.448 1.49,1.177 false 1.729,0.823 2.052,0.542 2.052,0.542 2.271,0.542 false 2.323,0.49 2.635,0.646 0.313,0.156 10 *1 0.865,1.365 1.177,1.521 0.313,0.156 10 *2
*1 Key A
*2 Key B


Install the starter armature plate to the starter yoke assembly.

NOTICE:

Install the starter armature plate so that the keyway is positioned between key A and key B.



b.
A298956
1.094,1.854 1.281,1.854 1.281,1.854 1.729,1.135 false 0.354,1.469 0.542,1.469 0.542,1.469 0.99,0.75 false 0.198,1.396 0.51,1.552 0.313,0.156 10 *1 0.948,1.781 1.26,1.938 0.313,0.156 10 *2
*1 Groove
*2 Cutout


Align the groove of the lead wire with the cutout of the starter commutator end frame assembly.


c.

Install the starter commutator end frame assembly with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


d.
A298957
1.417,2.052 1.583,2.052 1.583,2.052 1.708,1.573 false 2.26,2.021 2.396,2.021 2.396,2.021 2.552,1.458 false 1.271,1.958 1.583,2.115 0.313,0.156 10 *1 2.115,1.927 2.427,2.083 0.313,0.156 10 *2
*1 Claw
*2 Groove


Align the claw of the starter yoke assembly with the groove inside the starter drive housing assembly. Install the starter yoke assembly together with the starter armature assembly to the starter drive housing assembly.


e.

Using a T25 "TORX" socket wrench, install the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A298958
1.76,0.333 1.76,0.344 false
V100135

High-temperature Grease


Apply high-temperature grease to the plunger hook.


b.

Hang the plunger of the magnet starter switch assembly onto the drive lever from the upper side.


c.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the lead wire to the magnet starter switch assembly with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)