Home › Engine / Hybrid System › 3ZR-FE STARTING › STARTER(for 1.3 kW Type)
RM3090E _51 Engine / Hybrid System _008411 3ZR-FE STARTING _0049873 STARTER(for 1.3 kW Type) G

3ZR-FE STARTING  STARTER(for 1.3 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A264662
3.042,0.177 2.938,0.177 2.938,0.177 2.5,0.49 false 1.969,1.469 2.083,1.469 2.083,1.469 2.354,0.729 false 3.094,0.094 3.25,0.25 0.156,0.156 10 false *1 1.771,1.375 1.927,1.531 0.156,0.156 10 false *2
*1 Terminal 50
*2 Terminal C
V100135

Moves Outward


Connect the battery to the motor terminal starter kit as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the motor terminal starter kit.



c.
A264663
1.34,1.347 1.509,1.524 0.17,0.177 10 *1 1.528,1.44 1.636,1.44 1.636,1.44 2.103,0.72 false
*1 Terminal C
V100135

Disconnect


Perform a holding test.

i.

Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the motor terminal satarter kit.



d.
A264664
1.313,1.51 1.302,1.521 false
V100135

Disconnect
V100136

Returns Inward


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the result is not as specified, replace the motor teminal starter kit.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A264665
2.635,0.563 2.74,0.344 2.74,0.344 2.823,0.344 false 1.76,1.625 1.885,1.625 1.885,1.625 2.469,0.656 false 1.615,1.552 1.771,1.708 0.156,0.156 10 *1 2.844,0.26 3,0.417 0.156,0.156 10 *2
*1 Terminal 30
*2 Terminal 50
V100135

Connect


Connect the battery and an ammeter to the starter assembly as shown in the illustration.


iii.

Check that the starter assembly rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface. If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.
A073983
1.802,0.292 1.677,0.292 false 1.677,0.292 1.438,1.104 false 1.865,0.208 2.042,0.385 0.177,0.177 10 *1
*1 Segment


Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A073984
0.604,1.552 0.854,1.552 0.854,1.552 1.219,1.302 false 2.49,0.417 2.354,0.417 false 2.354,0.417 2.094,1.042 false 2.563,0.333 2.74,0.521 0.177,0.188 10 *1 0.406,1.438 0.583,1.615 0.177,0.177 10 *2
*1 Coil Core
*2 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A058584
2.792,0.948 2.969,1.146 0.177,0.198 10 *1
*1 Length


Using a vernier caliper, measure the protrusion length.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.8 mm (0.150 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A296793
2.823,0.781 3.135,0.938 0.313,0.156 10 *1
*1 Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard length:

9.0 mm (0.354 in.)


Minimum length:

4.0 mm (0.157 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.
A296794

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, replace the starter commutator end frame assembly.



Hide 28021 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planetary gears, and the internal gear and pinion gear of the starter center bearing clutch sub-assembly for wear or damage.

If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.


b.

Check the starter center bearing clutch pinion gear.

i.
A251384
1.365,0.667 1.354,0.667 false
V100135

Free
V100136

Lock


Hold the starter center bearing clutch sub-assembly, rotate the pinion gear clockwise and check that the pinion gear turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter center bearing clutch sub-assembly.



Hide 28226A 5.INSPECT MOTOR TERMINAL STARTER KIT

a.
A296795

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the motor terminal starter kit.



b.
G037611
2.26,0.396 2.125,0.396 false 2.125,0.396 1.823,1.167 false 0.802,1.833 0.958,1.833 0.958,1.833 1.385,1.354 false 0.635,1.74 0.813,1.896 0.177,0.156 10 false *1 2.292,0.302 2.469,0.458 0.177,0.156 10 false *2
*1 Terminal 50
*2 Terminal C


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the motor terminal starter kit.


ii.
G037612
1.073,1.958 1.219,1.958 1.219,1.958 1.417,1.594 false 1.417,0.417 1.604,0.135 1.604,0.135 1.708,0.135 false 0.885,1.854 1.052,2.021 0.167,0.167 10 false *1 1.74,0.052 1.906,0.219 0.167,0.167 10 false *2
*1 Terminal 50
*2 Motor terminal starter kit


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Motor terminal starter kit Always Below 2 Ω


If the result is not as specified, replace the motor terminal starter kit.