Home › Engine / Hybrid System › 3ZR-FE STARTING › STARTER(for 1.3 kW Type)
RM3090E _51 Engine / Hybrid System _008411 3ZR-FE STARTING _0049873 STARTER(for 1.3 kW Type) A

3ZR-FE STARTING  STARTER(for 1.3 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A196356
1.927,1.438 1.896,1.375 false
V100135

High-temperature Grease


Apply high-temperature grease to the drive lever set pin as shown in the illustration.


b.
A296798
1.354,1.979 1.521,1.979 1.521,1.979 1.521,1.729 false 1.49,0.75 1.906,0.75 false 1.365,0.656 1.677,0.813 0.313,0.156 10 *1 1.208,1.885 1.521,2.042 0.313,0.156 10 *2
*1 Drive Lever Set Pin
*2 Starter Center Bearing Clutch Sub-assembly


Install the drive lever set pin to the starter center bearing clutch sub-assembly.


c.

Install the starter center bearing clutch sub-assembly together with the drive lever set pin to the starter drive housing assembly.


Hide 2.INSTALL PLANETARY GEAR

a.
A296799
2.177,1.958 2.135,1.948 false
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears to the pins of the planetary shaft.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

NOTICE:

Do not drop the starter armature assembly.


a.
A264666
1.036,0.295 1.196,0.471 0.16,0.176 10 *1 1.036,0.886 1.196,1.062 0.16,0.176 10 *2 0.66,1.447 0.82,1.623 0.16,0.176 10 *3 1.611,0.393 1.245,0.393 false 1.611,0.984 1.245,0.984 false 0.869,1.545 1.047,1.545 1.047,1.545 1.537,2.143 false
*1 Snap Ring
*2 Plate Washer
*3 Bearing
V100135

High-temperature Grease


Apply high-temperature grease to the plate washer, a new snap ring and the bearing.


b.
A196360
1.083,1.302 1.063,1.302 false
V100135

High-temperature Grease


Apply high-temperature grease to the starter armature assembly as shown in the illustration.


c.

Install the starter armature assembly to the starter commutator end frame assembly.


d.

Install the plate washer to the starter armature shaft.


e.

Using snap ring pliers, install the snap ring.

NOTICE:
·

Be sure to install the snap ring in the armature shaft groove securely.

·

Be sure to properly install the snap ring because it easily expands.




f.
A300802
1.542,0.344 1.854,0.5 0.313,0.156 10 *1
*1 Length


Check the snap ring length.

i.

Using a vernier caliper, measure the snap ring length.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring.



Hide 28132A 4.INSTALL STARTER COMMUTATOR END FRAME COVER

A081178

a.

Install the starter commutator end frame cover to the starter commutator end frame assembly.


Hide 28177 5.INSTALL STARTER ARMATURE PLATE

a.
A073991
2.281,0.438 2.156,0.438 2.156,0.438 1.823,0.823 false 0.333,1.146 0.031,0.313 0.031,0.313 0.219,0.313 false 0.229,0.229 0.438,0.406 0.208,0.177 10 *2 2.313,0.365 2.521,0.521 0.208,0.156 10 *1
*1 Key
*2 Keyway


Align the keyway of the starter armature plate with the key inside the starter yoke assembly, and install the starter armature plate.


Hide 28130 6.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
G037250
1.677,0.75 0.906,0.323 0.906,0.323 0.75,0.323 false 2.208,0.552 1.635,0.073 1.635,0.073 1.479,0.073 false 1.281,0 1.448,0.156 0.167,0.156 10 *1 0.552,0.25 0.729,0.396 0.177,0.146 10 *2
*1 Rubber Part
*2 Groove


Align the rubber part on the starter commutator end frame assembly with the groove of the starter yoke assembly.


b.

Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A264667
0.656,1.865 0.771,1.865 0.771,1.865 1.208,1.396 false 1.667,0.854 1.552,0.854 1.552,0.854 1.354,1.406 false 0.51,1.792 0.667,1.969 0.156,0.177 10 *1 1.677,0.771 1.833,0.948 0.156,0.177 10 *2
*1 Groove
*2 Claw


Align the claw of the starter yoke assembly with the groove inside the starter drive housing assembly.


b.

Install the starter yoke assembly with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226A 8.INSTALL MOTOR TERMINAL STARTER KIT

a.
A196358

Apply high-temperature grease to the plunger and hook.


b.
A264668

Hang the plunger hook of the motor terminal starter kit on the drive lever set pin.


c.

Install the plunger and return spring.


d.

Install the motor terminal starter kit with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)