Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0049893 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/o Double Locking System)

a.
B171377
1.385,3.781 1.385,3.031 1.385,3.031 1.198,3.031 true 0.583,3.771 0.583,3.021 0.583,3.021 0.396,3.021 true 2.146,3.552 2.583,3.875 0.438,0.323 10 *c 2.677,3.198 3.115,3.594 0.438,0.396 10 *b 0.24,0.167 0.688,0.448 0.448,0.281 10 *a 0.271,2.948 0.708,3.365 0.438,0.417 10 L 1,2.948 1.385,3.365 0.385,0.417 10 UL
*a Component without harness connected
(Front Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the front door lock motor.

i.

Apply battery voltage and check the operation of the front door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Locks
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlocks


If the result is not as specified, replace the front door with motor lock assembly LH.



b.
B171377
1.073,4.167 1.073,4.521 1.073,4.521 1.313,4.521 true 0.896,4.167 0.896,4.521 0.896,4.521 0.698,4.521 true 2.167,3.563 2.417,3.802 0.25,0.24 10 *c 2.688,3.198 3.031,3.458 0.344,0.26 10 *b 0.167,0.156 0.708,0.635 0.542,0.479 10 *a 1.375,4.448 1.604,4.625 0.229,0.177 10 E 0.302,4.448 0.844,4.635 0.542,0.188 10 LSSR
*a Component without harness connected
(Front Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch (w/ Smart Entry and Start System or Theft Deterrent System).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - 8 (LSSR) Locked 10 kΩ or higher
Unlocked Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly LH.



c.
B273324
2.729,3.531 2.729,3.875 2.729,3.875 2.844,3.875 true 2.417,3.531 2.417,4.094 2.417,4.094 2.667,4.094 true 2.271,3.531 2.271,4.094 2.271,4.094 2.083,4.094 true 2.802,2.031 3.156,2.333 0.354,0.302 10 *b 2.99,0.969 3.292,1.302 0.302,0.333 10 *c 0.26,0.156 0.813,0.542 0.552,0.385 10 *a 2.896,3.802 3.146,4.083 0.25,0.281 10 E 2.729,4.021 3.01,4.333 0.281,0.313 10 L 1.885,4.021 2.323,4.302 0.438,0.281 10 UL
*a Component without harness connected
(Front Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the door key lock and unlock switch (for LHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Held to lock side Below 1 Ω
9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher
10 (UL) - 7 (E) Held to unlock side Below 1 Ω
10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly LH.



Hide 69040A 2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/ Double Locking System)

a.
B164418
0.646,3.823 0.646,2.49 0.646,2.49 0.729,2.49 true 0.406,3.833 0.406,2.583 0.406,2.583 0.323,2.583 true 0.833,3.813 0.833,3.146 0.833,3.146 0.917,3.146 true 1.146,3.885 1.479,3.885 true 0.167,0.115 0.688,0.51 0.521,0.396 10 *a 2.75,3.333 3.24,3.719 0.49,0.385 10 *b 2.229,3.74 2.531,4 0.302,0.26 10 *c 0.208,2.5 0.469,2.813 0.26,0.313 10 L 0.781,2.417 0.979,2.563 0.198,0.146 10 UL 0.948,3.073 1.146,3.219 0.198,0.146 10 DL 1.542,3.802 2.073,4.115 0.531,0.313 10 UNDL
*a Component without harness connected
(Front Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the front door lock motor.

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Locks
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlocks
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Sets
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door with motor lock assembly LH.



b.
B164418
0.979,4.125 0.979,4.333 0.979,4.333 1.479,4.333 true 0.667,4.135 0.667,4.417 0.667,4.417 0.5,4.417 true 0.833,4.125 0.833,4.5 0.833,4.5 1,4.5 true 1.167,4.063 1.583,4.063 true 0.24,0.146 0.771,0.552 0.531,0.406 10 *a 2.729,3.333 3.063,3.583 0.333,0.25 10 *b 2.229,3.74 2.604,3.99 0.375,0.25 10 *c 0.115,4.354 0.615,4.604 0.5,0.25 10 LSSR 1.052,4.438 1.167,4.583 0.115,0.146 10 E 1.542,4.271 2.042,4.521 0.5,0.25 10 DLSR 1.646,3.99 1.76,4.135 0.115,0.146 10 E
*a Component without harness connected
(Front Door with Motor Lock Assembly LH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Locked 10 kΩ or higher
8 (LSSR) - 7 (E) Unlocked Below 1 Ω
6 (DLSR) - 5 (E) Unset 10 kΩ or higher
6 (DLSR) - 5 (E) Set Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly LH.



Hide 69030A 3.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/o Double Locking System)

a.
B171378
2.854,3.792 2.854,3.125 2.854,3.125 3.021,3.125 true 2.052,3.792 2.052,3.125 2.052,3.125 2.219,3.125 true 0.208,0.146 0.729,0.542 0.521,0.396 10 *a 1.156,3.635 1.688,4.031 0.531,0.396 10 *c 0.615,3.229 0.948,3.594 0.333,0.365 10 *b 3.083,3.042 3.281,3.177 0.198,0.135 10 UL 2.302,3.042 2.396,3.177 0.094,0.135 10 L
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the front door lock motor.

i.

Apply battery voltage and check the operation of the front door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Locks
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlocks


If the result is not as specified, replace the front door with motor lock assembly RH.



b.
B273325
2.292,3.75 2.292,4.115 2.292,4.115 2.167,4.115 true 2.458,3.75 2.458,4.115 2.458,4.115 2.573,4.115 true 0.229,0.167 0.844,0.594 0.615,0.427 10 *a 1.104,3.177 1.521,3.531 0.417,0.354 10 *c 0.552,2.771 0.958,3.25 0.406,0.479 10 *b 2.021,4.042 2.323,4.333 0.302,0.292 10 E 2.646,4.042 3.177,4.385 0.531,0.344 10 LSSR
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly RH.



c.
B284859
0.75,3.427 0.75,4.438 0.75,4.438 0.906,4.438 true 1.052,3.427 1.052,4.135 1.052,4.135 1.208,4.135 true 1.208,3.427 1.208,3.823 1.208,3.823 1.365,3.823 true 0.958,4.354 1.26,4.542 0.302,0.188 10 E 1.26,4.042 1.802,4.396 0.542,0.354 10 L 1.406,3.729 1.979,4.083 0.573,0.354 10 UL 0.135,0.083 0.604,0.458 0.469,0.375 10 *a 0.604,1.615 1.125,1.938 0.521,0.323 10 *b 0.344,0.51 0.74,0.875 0.396,0.365 10 *c
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the door key lock and unlock switch (for RHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly RH.



Hide 69030A 4.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/ Double Locking System)

a.
B164417
2.344,3.865 2.344,2.115 2.344,2.115 2.906,2.115 true 2.781,3.865 2.781,2.875 2.781,2.875 3.146,2.875 true 2.563,3.865 2.563,2.531 2.563,2.531 2.906,2.531 true 3.01,3.865 3.01,3.146 3.01,3.146 3.146,3.146 true 0.115,0.052 0.656,0.51 0.542,0.458 10 *a 0.469,3.302 0.875,3.646 0.406,0.344 10 *b 1,3.771 1.375,4.125 0.375,0.354 10 *c 3.188,3.063 3.417,3.333 0.229,0.271 10 UL 3.188,2.792 3.354,3.021 0.167,0.229 10 L 2.948,2.448 3.385,2.698 0.438,0.25 10 UNDL 2.948,2.042 3.344,2.323 0.396,0.281 10 DL
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the front door lock motor.

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Locks
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlocks
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Sets
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door with motor lock assembly RH.



b.
B273326
2.292,3.708 2.292,4 2.292,4 1.781,4 true 2.448,3.708 2.448,4.26 2.448,4.26 1.781,4.26 true 2.583,3.708 2.583,4.51 2.583,4.51 1.771,4.51 true 2.719,3.708 2.719,4.063 2.719,4.063 2.865,4.063 true 0.198,0.167 0.729,0.573 0.531,0.406 10 *a 0.458,2.813 0.833,3.156 0.375,0.344 10 *b 1.052,3.271 1.458,3.583 0.406,0.313 10 *c 2.917,3.99 3.365,4.26 0.448,0.271 10 LSSR 1.635,4.438 2.073,4.656 0.438,0.219 10 E 1.365,4.188 2.063,4.406 0.698,0.219 10 DLSR 1.646,3.927 2.01,4.229 0.365,0.302 10 E
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the door unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly RH.



c.
B259282
1,3.958 1,4.385 1,4.385 0.875,4.385 true 1.323,3.958 1.323,4.49 1.323,4.49 1.656,4.49 true 1.469,3.969 1.469,4.26 1.469,4.26 1.656,4.26 true 0.177,0.125 0.563,0.375 0.385,0.25 10 *a 0.823,2.427 1.208,2.667 0.385,0.24 10 *c 1.208,1.021 1.51,1.313 0.302,0.292 10 *b 1.698,4.198 2.188,4.385 0.49,0.188 10 UL 1.708,4.438 1.938,4.604 0.229,0.167 10 L 0.74,4.333 1,4.531 0.26,0.198 10 E
*a Component without harness connected
(Front Door with Motor Lock Assembly RH)
*b Unlock
*c Lock


Check the operation of the door key lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly RH.