Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049189 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1413  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1413 Evaporator Temperature Sensor Circuit Open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E236721E32
2.146,0.438 2.552,0.948 0.406,0.51 10 2 2.156,1.385 2.417,1.729 0.26,0.344 10 1 5.125,0.438 5.302,0.615 0.177,0.177 10 15 5.208,1.385 5.385,1.563 0.177,0.177 10 4 5.417,0.563 5.958,0.969 0.542,0.406 10 SG-1 5.417,1.51 5.771,1.802 0.354,0.292 10 TE 1.063,1.917 1.385,2.094 0.323,0.177 10 G30 1.083,2.083 2.625,2.552 1.542,0.469 10 No. 1 Cooler Thermistor 5.063,1.885 5.385,2.167 0.323,0.281 10 G80 5.063,2.042 6.635,2.552 1.573,0.51 10 Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor Min.: -29.7°C (21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT NO. 1 COOLER THERMISTOR
2.INSPECT NO. 1 COOLER THERMISTOR


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 COOLER THERMISTOR)

NG

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - NO. 1 COOLER THERMISTOR)
a.

Disconnect the G80 air conditioning amplifier assembly connector.


b.

Disconnect the G30 No. 1 cooler thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-15 (SG-1) - G30-2 Always Below 1 Ω
G80-4 (TE) - G30-1 Always Below 1 Ω
G80-15 (SG-1) - Body ground Always 10 kΩ or higher
G80-4 (TE)- Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR