Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › 2012.12–2014.10
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050008 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 52711 1.INSTALL FRONT BUMPER MOULDING

a.

Install the front bumper moulding with the 9 retainers.


Hide 52411 2.INSTALL FRONT BUMPER GUARD

a.

Install the front bumper guard with the 8 retainers.


Hide 53128A 3.INSTALL LOWER RADIATOR GRILLE LH

a.

Attach the 4 claws to install the lower radiator grille LH.


b.

Install the 2 clips.


Hide 53127A 4.INSTALL LOWER RADIATOR GRILLE RH

HINT:

Use the same procedure described for the LH side.


Hide 53128A 5.INSTALL LOWER RADIATOR GRILLE LH (for Automatic Transaxle (U660F))

a.

Attach the 4 claws to install the lower radiator grille LH.


b.

Install the 2 clips.


Hide 53112E 6.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.

Attach the 18 claws to install the lower No. 1 radiator grille.


Hide 52113D 7.INSTALL FRONT BUMPER EXTENSION LH

a.

Install the front bumper extension LH with the 5 retainers.


Hide 52112D 8.INSTALL FRONT BUMPER EXTENSION RH

HINT:

Use the same procedure described for the LH side.


Hide 53286C 9.INSTALL FRONT BUMPER ARM HOLE COVER LH

a.

Attach the 2 claws to install the front bumper arm hole cover LH.


Hide 53285J 10.INSTALL FRONT BUMPER ARM HOLE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 75301A 11.INSTALL FRONT BUMPER EMBLEM SUB-ASSEMBLY

a.

Attach the 2 claws to install the front bumper emblem sub-assembly.


Hide 53106C 12.INSTALL RADIATOR GRILLE GARNISH SUB-ASSEMBLY LH

a.

Attach the 4 clips to install the radiator garnish sub-assembly LH.


b.

Detach the claw.


c.

Install the 2 screws.


Hide 53105A 13.INSTALL RADIATOR GRILLE GARNISH SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52128C 14.INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

a.

Install the front bumper hole cover LH with the 2 screws.


b.

Install the clip.


Hide 52127D 15.INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 52128C 16.INSTALL FRONT BUMPER HOLE COVER LH (w/ Fog Light)

a.

Install the front bumper hole cover LH with the 2 screws.


b.

Install the clip.


Hide 52127D 17.INSTALL FRONT BUMPER HOLE COVER RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 81220 18.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 19.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 53395E 20.INSTALL HOOD TO FRONT END PANEL SEAL

HINT:

When installing the hood to front end panel seal, heat the front bumper cover using a heat light.


Standard:
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

When reusing the front bumper cover:

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove the double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

Install a new hood to front end panel seal.

i.

Using a heat light, heat the front bumper cover.


ii.

Remove the peeling paper from the face of the hood to front end panel seal.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 9 clips to install the hood to front end panel seal.

HINT:

Press the hood to front end panel seal firmly to install it.




Hide 85208A 21.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 22.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.


Hide 23.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

Hide 85045 24.INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85044 25.INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure described for the LH side.