Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) U

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A295480E02
1.563,0.417 1.896,0.667 0.333,0.25 3.167,0.417 3.5,0.667 0.333,0.25 5,0.417 5.333,0.667 0.333,0.25 1.615,0.469 1.927,0.667 0.313,0.198 10 A65 3.219,0.469 3.531,0.667 0.313,0.198 10 A66 5.052,0.469 5.365,0.667 0.313,0.198 10 G87

a.

Disconnect the A65, A66 and G87 engine stop and start ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A65-5 (+B) - Body ground B - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A65-7 (BIN) - Body ground L - Body ground Battery Always 9.5 to 14 V
A65-8 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-10 (NE) - Body ground P - Body ground Engine speed signal from ECM Always 10 kΩ or higher
A66-17 (VB-) - Body ground W-B - Body ground Ground Always Below 1 Ω
G87-15 (CANH) - Body ground LG - Body ground CAN communication Always 200 Ω or higher
G87-16 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G87-17 (IG1) - Body ground L - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - Body ground W - Body ground Ignition switch signal Ignition switch ACC 9.5 to 14 V
G87-20 (IG2) - Body ground V - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the A65, A66 and G87 engine stop and start ECU connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A66-3 (BRE2) - Body ground G - Body ground Ground (vacuum sensor assembly (brake booster pressure sensor)) Always Below 1 Ω
A66-7 (BNT1) - A65-8 (GND) R - W-B Engine hood courtesy switch (hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A66-10 (NE) - A65-8 (GND) P - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 1)
A66-11 (CLU) - A65-8 (GND) L - W-B Clutch switch assembly (for upper) signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A66-13 (PB) - A66-3 (BRE2) B - G Vacuum sensor assembly (brake booster pressure sensor) signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly (brake booster pressure sensor)


3.4 to 3.8 V
A66-14 (BRVC) - A65-8 (GND) P - W-B Vacuum sensor assembly (brake booster pressure sensor) power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A66-21 (STA) - A65-8 (GND) LG - W-B Starter operation signal Ignition switch ON 0 V to 1.5 V
Cranking 6 V to 14 V
A66-26 (TMVC) - A65-8 (GND) G - W-B Neutral position switch power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A66-27 (TMN) - A66-25 (TME2) LG - BR Neutral position switch signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
A66-28 (CLL) - A65-8 (GND) W - W-B Clutch start switch assembly (for lower) signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
G87-2 (BO1) - A65-8 (GND) SB - W-B Backup boost converter signal Always 9.5 to 14 V
G87-3 (ACO) - A65-8 (GND) GR - W-B Backup boost converter signal Ignition switch ACC 9.5 to 14 V
G87-4 (CHI) - A65-8 (GND)* BR - W-B Combustion type Power heater system operating signal
·

Ignition switch ON

·

Heater switch assembly on


9.5 to 14 V
·

Ignition switch ON

·

Heater switch assembly off


Below 1 V
G87-11 (IGO2) - A65-8 (GND) P - W-B Backup boost converter signal Ignition switch ON 9.5 to 14 V
G87-12 (IGO1) - A65-8 (GND) L - W-B Backup boost converter signal Ignition switch ON 9.5 to 14 V
G87-17 (IG1) - A65-8 (GND) L - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - A65-8 (GND) W - W-B Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
G87-20 (IG2) - A65-8 (GND) V - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-23 (ECAN) - A65-8 (GND) V - W-B Stop and start system cancel switch (combination switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (combination switch assembly) pressed


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (combination switch assembly) not press


8 to 14 V

*: w/ Combustion Type Power Heater System



e.
A278994E02
2.969,1.26 3.427,1.458 0.458,0.198 10 GND

Waveform 1

Engine Speed Signal
Item Content
Tester Connection A66-10 (NE) - A65-8 (GND)
Tool Setting 5 V/DIV, 2 ms/DIV
Condition Idling after engine warmed up

HINT:

The wavelength become shorter as the engine speed increases.