The engine stop and start ECU communicates with the ECD system, anti-lock brake system, power steering system, meter/gauge system, air conditioning system, lane departure alert system, airbag system and main body ECU (multiplex network body ECU) via CAN communication.
If an error occurs in communication between the engine stop and start ECU and any of the systems, the engine stop and start ECU stores DTCs and illuminates the stop and start cancel indicator light except when there is a communication error with the meter/gauge system.
When there is an open in the output side of the backup boost converter (built-into the engine stop and start ECU), power to the system with an open circuit is cut off. The engine stop and start ECU stores CAN communication DTCs for the system with an open circuit and stop and start system DTC P323B.
When the backup boost converter (built-into the engine stop and start ECU) detects overcurrent in any of the circuits it supplies power to, it shuts off the circuit. The engine stop and start ECU stores CAN communication DTCs for the system which circuit was shutoff and stores stop and start system DTC B22C0.
e.g.: When the backup boost converter (built into the engine stop and start ECU) detects overcurrent in the power source circuit of the power steering system and cuts off power supply, the engine stop and start ECU stores DTC U0131 and DTC B22C0.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | No communication between the engine stop and start ECU and the ECM for 0.8 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
ECM |
Blinking | DTC stored |
| U0121 | Lost Communication with Anti-lock Brake System (ABS) Control Module | No communication between the engine stop and start ECU and the skid control ECU (brake actuator assembly) for 2.3 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Skid control ECU (brake actuator assembly) |
Blinking | DTC stored |
| U0131 | Lost Communication with Power Steering Control Module | No communication between the engine stop and start ECU and the power steering ECU assembly for 0.8 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Power steering ECU assembly |
Blinking | DTC stored |
| U0140 | Lost Communication with J/B ECU | No communication between the engine stop and start ECU and the main body ECU (multiplex network body ECU) for 3.6 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Main body ECU (multiplex network body ECU) |
Blinking | DTC stored |
| U0151 | Lost Communication with SRS Airbag ECU | No communication between the engine stop and start ECU and the airbag sensor assembly for 10.6 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Airbag sensor assembly |
Blinking | DTC stored |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | No communication between the engine stop and start ECU and the combination meter assembly for 10.6 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Combination meter assembly |
Blinking | DTC stored |
| U0164 | Lost Communication with HVAC Control Module | No communication between the engine stop and start ECU and the air conditioning amplifier assembly for 10.6 seconds. | ·
Wire harness or connector ·
Engine stop and start ECU ·
Air conditioning amplifier assembly |
Blinking | DTC stored |
If any of CAN communication system DTCs and sensor malfunction DTCs related to the CAN communication system are output simultaneously, perform troubleshooting for the CAN communication system DTCs first, then for the sensor malfunction DTCs.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON.
Start the engine.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC U0100, U0121, U0131, U0140, U0151, U0155 or U0164 is output | A |
| DTC U0100, U0121, U0131, U0140, U0151, U0155 or U0164 is not output | B |
A
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING