Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050099 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E270671
0.875,0.552 1.031,0.75 0.156,0.198 10 1 0.708,1.094 0.865,1.292 0.156,0.198 10 2

Move the windshield wiper motor assembly in the direction of the arrows as shown in the illustration and attach it to the link.


b.

Install the windshield wiper motor assembly with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.
E268333
1.594,1.406 1.625,1.344 false
V100155

MP Grease


Apply MP grease to the wiper motor pivot.


d.
E268334

Connect the No. 1 rod to the wiper motor pivot.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.


a.

Connect the connector and attach the clamp.


b.
E268335
1.969,0.417 2.219,0.281 false 2.208,0.156 2.521,0.354 0.313,0.198 10 *1
*1 Motor Grommet


Attach the motor grommet as shown in the illustration.


c.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Attach the 9 guides as shown in the illustration.

E268336


b.

Attach the 5 claws and 2 guides to install the cowl top ventilator louver sub-assembly as shown in the illustration.

E268337


c.

Install the 2 clips.


Hide 53867H 4.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.
E268325
2.125,0.771 2.906,1.51 true 2.938,1.5 3.25,1.698 0.313,0.198 10 *1
*1 Double-sided Tape


Apply Primer G to the installation part of the spacer.

NOTICE:
·

Clean the front fender to cowl side seal installation area on the body using non-residue solvent.


·

If an area other than specified is coated by accident, wipe off the Primer G with a clean piece of cloth before it dries.




b.

Apply double-sided tape to the front fender to cowl side seal.


c.

Attach the claw and 3 guides to install the front fender to cowl side seal LH.


Hide 53866J 5.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 6.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

a.

Stop the windshield wiper motor assembly at the automatic stop position.


b.
E268607
2.5,1.25 1.917,1.25 true 1.917,3.5 2.583,3.5 true 2.573,1.188 2.885,1.385 0.313,0.198 10 *1 2.646,3.438 2.958,3.635 0.313,0.198 10 *2
*1 Wiper Arm Serration
*2 Wiper Pivot Serration


When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations.



d.
E268338
0.469,2.698 0.479,3 0.479,3 0.729,3 false 0.781,2.927 1.104,3.073 0.323,0.146 10 *1
*1 Ceramic Dot


Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 7.INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

a.
E268607
2.5,1.25 1.917,1.25 true 1.917,3.5 2.583,3.5 true 2.573,1.188 2.885,1.385 0.313,0.198 10 *1 2.646,3.438 2.958,3.635 0.313,0.198 10 *2
*1 Wiper Arm Serration
*2 Wiper Pivot Serration


When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations.



c.
E268339
0.833,2.917 0.5,2.917 0.5,2.917 0.5,2.458 false 0.885,2.833 1.198,3.031 0.313,0.198 10 *1
*1 Ceramic Dot


Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



d.

Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.


e.

Lift each front wiper blade twice after the front wipers stop and check the wiper set position.


Hide 85192 8.INSTALL WINDSHIELD WIPER ARM COVER

a.

Attach the 3 claws to install the windshield wiper arm cover.

HINT:

Use the same procedure for both windshield wiper arm covers.