Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050099 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E268321
0.333,2 0.656,2 0.656,2 0.656,1.906 true 0.969,4.521 0.719,4.521 0.719,4.521 0.719,4.229 true 0.354,4.052 0.323,4.375 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *A 0.052,2.26 0.365,2.458 0.313,0.198 10 false *B 0.865,2.094 1.021,2.292 0.156,0.198 10 false a 0.167,4.177 0.323,4.375 0.156,0.198 10 false b 0.167,1.917 0.479,2.115 0.313,0.198 10 false *1 1,4.448 1.313,4.646 0.313,0.198 10 false *1 0.281,4.396 0.594,4.594 0.313,0.198 10 false *2
*A for LH Side
*B for RH Side
*1 Louver Lip Edge
*2 Fender to cowl seal Lip Edge


Operate the windshield wiper motor assembly.


b.

Stop the windshield wiper motor assembly operation.


c.

Check the automatic stop (park) position.

OK:

The front wiper blade stops at the position shown in the illustration.


Standard:
Area Standard Condition
a 28.4 mm (1.11 in.)
b 25 mm (0.98 in.)


HINT:

After the front wiper blade is stopped, check the automatic stop position after lifting the front wiper blade 2 times.



Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E271069
3,2.146 2.833,2.146 2.833,2.146 2.833,1.896 true 2.708,4.25 2.708,4.5 2.708,4.5 2.542,4.5 true 3.135,4.073 3.104,4.438 true 0,0 0.313,0.156 0.313,0.156 10 false *A 0.083,2.24 0.396,2.396 0.313,0.156 10 false *B 3.042,2.073 3.354,2.229 0.313,0.156 10 false *1 2.406,4.427 2.719,4.583 0.313,0.156 10 false *1 2.583,2.104 2.896,2.26 0.313,0.156 10 false a 3.208,4.188 3.313,4.365 0.104,0.177 10 false b 3.042,4.438 3.354,4.594 0.313,0.156 10 false *2
*A for RH Side
*B for LH Side
*1 Louver Edge
*2 Fender to cowl seal Lip Edge


Operate the windshield wiper motor assembly.


b.

Stop the windshield wiper motor assembly operation.


c.

Check the automatic stop (park) position.

OK:

The front wiper blade stops at the position shown in the illustration.


Standard:
Area Standard Condition
a 28.4 mm (1.11 in.)
b 25 mm (0.98 in.)


HINT:

After the front wiper blade is stopped, check the automatic stop position after lifting the front wiper blade 2 times.