Home › Vehicle Exterior › LIGHTING (EXT) › HIGH INTENSITY DISCHARGE HEADLIGHT BULB(for HID Headlight) › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0050101 HIGH INTENSITY DISCHARGE HEADLIGHT BULB(for HID Headlight) G

LIGHTING (EXT)  HIGH INTENSITY DISCHARGE HEADLIGHT BULB(for HID Headlight)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 81110L 1.INSPECT DISCHARGE HEADLIGHT BULB

NOTICE:

Confirm the following items before replacing a discharge headlight bulb. If a malfunction is discovered and repaired, perform the inspection again to confirm the repair.

·

Make sure that the high voltage socket of the headlight light control ECU sub-assembly and discharge headlight bulb are connected securely.

·

Make sure that there is no damage to the high voltage socket of the headlight light control ECU sub-assembly or discharge headlight bulb connector.



HINT:

Even if a bulb seems to turn on normally, it may not be normal. Perform all the following steps in order because an abnormal condition might otherwise not be easy to duplicate.


a.

Prepare the vehicle:

Before performing the following inspection procedure, turn off the discharge headlight bulbs for more than 10 minutes to allow them to cool down sufficiently.

HINT:

Since it is necessary to find the cause of a malfunction that causes a discharge headlight bulb not to turn on, the discharge headlight bulbs should be inspected starting from a cooled state.


i.

Turn on the discharge headlights for more than 25 minutes, and check that the bulbs remain illuminated normally.

HINT:
·

Leave the headlights on for more than 25 minutes to stabilize the discharge headlight bulb arc tube voltage.

·

A discharge headlight bulb that has almost reached the end of its life may turn off due to a headlight light control ECU sub-assembly fail-safe function because the arc tube voltage is high.




ii.

Repeatedly turn the discharge headlights off for 15 seconds and on for 15 seconds (5 times for each). Check that the bulbs illuminate normally.

HINT:

This inspection confirms the ability of the bulbs to start when hot.



iii.

Turn off the discharge headlights for 3 minutes, and then turn on the discharge headlights for 3 minutes. Check that the bulbs illuminate normally when they are turned on.

HINT:
·

A characteristic of discharge headlight bulbs is that their starting voltage is highest when 3 minutes have elapsed after being turned off. This is the most difficult situation for discharge bulbs to start in.

·

This inspection is further confirmation of the ability of the bulbs to start when hot.



E168986C01
0.073,0.021 2.958,0.219 2.885,0.198 10 Discharge headlight bulb inspection procedure 1.469,0.365 2.24,0.531 0.771,0.167 10 Preparation 2.771,0.365 3.365,0.563 0.594,0.198 10 Step (1) 3.875,0.365 4.438,0.563 0.563,0.198 10 Step (2) 4.719,0.365 5.292,0.563 0.573,0.198 10 Step (3) 5.573,0.365 5.979,0.563 0.406,0.198 10 Finish 1.219,2.052 1.438,2.25 0.219,0.198 10 Off 1.198,1.417 1.417,1.615 0.219,0.198 10 On 1.781,2.198 2.094,2.354 0.313,0.156 10 *a 2.906,1.271 3.219,1.427 0.313,0.156 10 *b 4.073,1.073 4.385,1.229 0.313,0.156 10 *c 5.052,1.292 5.365,1.448 0.313,0.156 10 *d 3.979,2.396 4.125,2.563 0.146,0.167 10 *c 4.646,2.198 4.958,2.354 0.313,0.156 10 *d
*a More than 10 minutes *b More than 25 minutes
*c 15 seconds *d 3 minutes


Standard:

The discharge headlight bulbs illuminate normally in all steps.



iv.

Remove the discharge headlight bulb and perform a visual inspection of the arc tube.

Standard:

The inside of the arc tube is not bulging or deformed and is not clouded.


HINT:

However, a dull brown coloration inside the arc tube is normal.


E206653C13
5.74,2.896 6.469,3.094 true 2.292,2.906 3.021,3.104 true 3.083,3.052 3.458,3.271 0.375,0.219 10 *c 6.542,3.042 6.875,3.24 0.333,0.198 10 *c 0.531,0.333 0.823,0.542 0.292,0.208 10 *a 4,0.333 4.292,0.542 0.292,0.208 10 *b
*a Discharge headlight bulb is normal *b Discharge headlight bulb at end of usable life
*c Arc Tube - -
V100145

Inside of Arc Tube
V100144

Distortion / Clouded Area