Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM3090E _59 Vehicle Exterior _008431 MIRROR (EXT) _0050127 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

i.
B322111
0.896,0.74 1.427,0.938 true 1.323,1.458 0.833,1.542 true 1.302,4.135 1.479,3.604 true 1.938,4.125 1.979,3.583 true 2.24,4.135 2.125,3.594 true 1.594,4.125 1.656,3.604 true 2.563,4.135 2.281,3.594 true 2.885,4.125 2.427,3.604 true 0.979,4.115 1.156,3.604 true 0.667,0.656 0.979,0.813 0.313,0.156 10 *1 0.635,1.479 0.948,1.635 0.313,0.156 10 *2 0.188,2.271 0.385,2.427 0.198,0.156 10 *a 0.917,4.167 1.073,4.365 0.156,0.198 10 B 1.25,4.167 1.406,4.365 0.156,0.198 10 E 1.521,4.167 1.833,4.365 0.313,0.198 10 M+ 1.854,4.167 2.167,4.365 0.313,0.198 10 HL 2.188,4.167 2.5,4.365 0.313,0.198 10 VL 2.5,4.167 2.813,4.365 0.313,0.198 10 VR 2.854,4.167 3.167,4.365 0.313,0.198 10 HR
*1 Mirror Select Switch
*2 Mirror Surface Adjust Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
16 (VL) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
16 (VL) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
15 (VR) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
15 (VR) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

i.
B340951
0.938,0.677 1.313,0.896 true 2.208,0.938 2.688,0.677 true 1.365,1.479 0.927,1.479 true 0.333,3.917 0.833,3.583 true 0.583,4.083 1,3.583 true 1,4.083 1.167,3.583 true 1.365,4.083 1.49,3.594 true 2.25,4.083 2.104,3.594 true 2.438,3.604 2.917,4.083 true 1.594,4.073 1.635,3.604 true 1.969,4.073 1.969,3.583 true 2.583,4.083 2.281,3.604 true 0.781,0.604 1.094,0.76 0.313,0.156 10 *1 0.75,1.406 1.063,1.563 0.313,0.156 10 *2 2.771,0.594 3.083,0.75 0.313,0.156 10 *3 0.094,2.323 0.406,2.479 0.313,0.156 10 *a 2.917,4.135 3.229,4.333 0.313,0.198 10 HR 2.521,4.135 2.833,4.333 0.313,0.198 10 VR 2.188,4.135 2.5,4.333 0.313,0.198 10 VL 1.521,4.135 1.833,4.333 0.313,0.198 10 M+ 1.302,4.135 1.458,4.333 0.156,0.198 10 E 0.917,4.135 1.073,4.333 0.156,0.198 10 B 0.438,4.135 0.75,4.333 0.313,0.198 10 MR 0.104,3.833 0.417,4.031 0.313,0.198 10 MF 1.896,4.135 2.208,4.333 0.313,0.198 10 HL
*1 Mirror Select Switch
*2 Mirror Surface Adjust Switch
*3 Retract Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
16 (VL) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
16 (VL) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
15 (VR) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
15 (VR) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
24 (MF) - 20 (E)
23 (MR) - 22 (B)
Pushed in Below 1 Ω
24 (MF) - 22 (B)
23 (MR) - 20 (E)
Not pushed in Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.