Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0050132 SFI SYSTEM C

3ZR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and sets the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON.
(b) STP signal is off when ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A298878E01
0.563,3.865 1.188,4.115 0.625,0.25 10 false Battery 0.635,0.615 1.042,0.854 0.406,0.24 10 false ALT 4.052,0.625 4.458,0.865 0.406,0.24 10 false STOP 0.656,1.406 1.063,1.646 0.406,0.24 10 false IG2 3.24,2.219 3.646,2.458 0.406,0.24 10 false IG2 4.115,1.406 4.521,1.646 0.406,0.24 10 false IGN 4.646,1.604 4.938,1.823 0.292,0.219 10 false A5 4.625,1.781 5.74,2.219 1.115,0.438 10 false Stop Light Switch Assembly 6.25,0.354 6.656,0.594 0.406,0.24 10 false STP 6.24,1.146 6.646,1.385 0.406,0.24 10 false ST1- 6.448,2.75 6.854,2.99 0.406,0.24 10 false ECM 6.458,2.583 6.865,2.823 0.406,0.24 10 false A62 6.021,0.354 6.219,0.583 0.198,0.229 10 false 9 5.958,1.146 6.365,1.385 0.406,0.24 10 false 10 5.552,1.146 5.74,1.344 0.188,0.198 10 false 3 4.646,1.135 4.833,1.333 0.188,0.198 10 false 4 5.542,0.344 5.729,0.542 0.188,0.198 10 false 1 4.646,0.354 4.833,0.552 0.188,0.198 10 false 2 3.719,1.125 3.906,1.323 0.188,0.198 10 false 5 2.844,1.146 3.031,1.344 0.188,0.198 10 false 3 3.719,1.76 3.906,1.958 0.188,0.198 10 false 2 2.833,1.771 3.021,1.969 0.188,0.198 10 false 1 4.635,3.896 6.625,4.135 1.99,0.24 10 false *1: w/ Entry and Start System 4.635,4.229 6.625,4.469 1.99,0.24 10 false *2: w/o Entry and Start System 1.219,3.938 2.781,4.375 1.563,0.438 10 false Certification ECU (Smart Key ECU Assembly)*1 1.219,3.76 1.51,3.979 0.292,0.219 10 false G82 1.813,3.375 2.167,3.583 0.354,0.208 10 false IG2D 2.25,3.25 2.438,3.448 0.188,0.198 10 false 9 0.938,2.271 1.229,2.49 0.292,0.219 10 false G4 0.948,2.427 2.792,2.625 1.844,0.198 10 false Ignition Switch Assembly*2 1.969,1.76 2.323,1.969 0.354,0.208 10 false IG2 1.354,1.771 1.708,1.979 0.354,0.208 10 false AM2 0.625,2.042 0.979,2.25 0.354,0.208 10 false AM2 2.302,1.76 2.49,1.958 0.188,0.198 10 false 3 1.177,1.771 1.365,1.969 0.188,0.198 10 false 4 2.458,1.813 2.646,2.01 0.188,0.198 10 false *2 2.458,3.281 2.646,3.479 0.188,0.198 10 false *1 0.948,1.813 1.135,2.01 0.188,0.198 10 false *2 0.406,2.792 1.031,3.042 0.625,0.25 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A200909C04
0.552,0.917 1.01,1.188 0.458,0.271 0.688,0.979 1.021,1.156 0.333,0.177 10 A5 0.125,0.052 0.344,0.24 0.219,0.188 10 *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A200909C04
0.552,0.917 1.01,1.188 0.458,0.271 0.688,0.979 1.021,1.156 0.333,0.177 10 A5 0.125,0.052 0.344,0.24 0.219,0.188 10 *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP AND ST1 - VOLTAGE)
a.
A298902C01
0.188,3.302 0.615,3.646 0.427,0.344 2.896,4.25 2.594,3.24 true 2.229,4.271 2.51,3.24 true 0.698,1.792 1.01,1.948 0.313,0.156 10 false *a 2.365,1.792 2.677,1.948 0.313,0.156 10 false *b 0.156,2.542 0.469,2.698 0.313,0.156 10 false *c 0.281,3.396 0.74,3.594 0.458,0.198 10 false A62 2.063,4.323 2.396,4.521 0.333,0.198 10 false STP 2.802,4.302 3.135,4.5 0.333,0.198 10 false ST1-
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-10 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A62-9 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)