Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) D

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  SYSTEM DESCRIPTION  


STOP AND START CONTROL


The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.

a.

When all of the conditions in the following table have been met, the engine is stopped by stop and start system control.

Item Condition
(All of the following conditions are met)
Idle Stop Ignition Switch 5 seconds or more have passed with the ignition switch ON
Engine Coolant Temperature Within the specified temperature range (varies depending on the vehicle usage environment)
HINT:
·

The upper limit is 105°C (221°F)

·

The lower limit is maximum 65°C (149°F)



Atmospheric Pressure 75 kPa (0.8 kgf/cm2, 11 psi) or higher
Ambient Temperature -5°C (23°F) or higher
Driver Door Closed
Driver Seat Belt Fastened
Brake Booster Vacuum Sufficient
Shift Position Shift lever in neutral
Stop and Start System Cancel Switch Off (system control is not prohibited)
Vehicle Speed 0 km/h (0 mph) (After the engine warms up)
Engine Speed 1250 rpm or less
Engine Hood Closed
Battery Voltage 6.6 V or higher at engine start
Battery Temperature*1 -10 to 70°C (14 to 158°F)
Battery Integrated Current*2
1.

0 A-sec or higher: After engine start by ignition switch operation

2.

The integrated current value has increased to 0 A-sec or higher at least once after ignition switch ON:

HINT:

The engine is stopped until the following conditions are not met:

·

-6451 A-sec or higher: The battery charge is sufficient and the battery temperature is -1°C (30.2°F) or higher and below 70°C (158°F)

·

-1152 A-sec or higher: The battery charge is insufficient or the battery temperature is below -1°C (30.2°F) or 70°C (158°F) or higher




Air Conditioning Other than when stop and start control is prohibited
Heater Once of the following conditions is met:
·

The blower switch is off

·

The blower switch is on when the Ambient temperature is 11°C (51.8°F) or higher or the engine coolant temperature is 46°C (114.8°F) or higher

·

0 to 20 seconds after the engine is restarted by stop and start control, and the air conditioning switch is off, or the blower switch is off.



HINT:
·

*1: When the battery temperature is -15°C (5°F) or less, or 75°C (167°F) or higher, the stop and start control is prohibited. When the battery temperature returns to -10°C (14°F) or higher, or 70°C (158°F) or less, stop and start control is permitted.

·

*2: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DATA LIST / ACTIVE TEST




b.

When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.

Item Condition
(Any of the following conditions are met)
Engine Restart Brake Booster Vacuum The brake booster vacuum is insufficient
Air Conditioning The timer in the air conditioning amplifier assembly runs out
Heater When the blower is in auto mode, the timer in the air conditioning amplifier assembly runs out. In other conditions, the timer in the engine stop and start ECU runs out
Air Conditioning/Heater
·

A/C switch, blower switch: ON

·

Defogger switch: ON

·

The blower switch is turned off during auto control or the blower mode is changed to manual

·

Pollen mode switch: ON


Battery Battery performance or voltage drops
Vehicle Speed Vehicle speed signal is input
Driver Door Open
Driver Seat Belt Driver seat belt is unfastened
Stop and Start System Cancel Switch Stop and start system cancel switch (combination switch assembly) is turned from off to on
Heater Switch Assembly* The heater switch assembly is turned on

*: w/ Combustion Type Power Heater System



SYSTEM PROHIBITION CONTROL


The engine stop and start ECU prohibits stop and start control by the stop and start system according to the table below. The prohibition conditions are specified for each system.

Item Prohibition Condition Vehicle State Restoration Condition Prohibition Condition Check Timing
Engine Not within the specified temperature range (varies depending on the vehicle usage environment)
HINT:
·

The upper limit is 105°C (221°F)

·

The lower limit is maximum 65°C (149°F)



Engine has not warmed up Within the specified temperature range (varies depending on the vehicle usage environment) Always
Atmospheric pressure 75 kPa (0.8 kgf/cm2, 11 psi) or less - Atmospheric pressure 75 kPa (0.8 kgf/cm2, 11 psi) or higher Always
DPF warning light on (Excessive PM accumulation) - DPF warning light off (PM regeneration complete) Always
Brake Brake booster vacuum decreases Brake booster vacuum decreases due to pumping the brakes, etc Normal brake booster vacuum is reached Every time the vehicle stops
Air Conditioning Heater:
All of the following conditions are met:
·

Blower switch is on

·

Ambient temperature is 10°C (50°F) or less

·

Coolant temperature is less than 45°C (113°F)


Heater performance decreases
·

Coolant temperature is 45°C (113°F) or higher

·

Blower switch is off


While the heater is on
Heater switch is on (for Combustion Type Power Heater System) - Heater switch is off (for Combustion Type Power Heater System) While the heater is on
Cooling function:
All of the following conditions are met:
·

Blower switch is on

·

Air conditioning switch is on

·

Ambient temperature is 25°C (77°F) or higher

·

Evaporator temperature is 9°C (48.2°F) or higher


Cooling performance decreases Any of the following conditions have been met:
·

Evaporator temperature is 9°C (48.2°F) or less

·

Blower switch is off

·

Air conditioning switch is off


While the air conditioning system (cooling function) is on
Defogger:
All of the following conditions have been met:
1.

Blower switch is on

2.

0 to 20 seconds after the engine is restarted by stop and start control when the ambient temperature is -7°C (19.4°F) or higher and the blower switch and air conditioning switch are on


1.

Fogging of windows

2.

Air conditioning performance decreases

3.

Odor from air vents


1.

Blower switch is off

2.

0 to 20 seconds have passed after restarting the engine by the stop and start control or the air conditioning switch is off, or blower switch is off.


While the air conditioning system (cooling function for defogger) is on
Driver Door Driver door is opened before engine stop by engine stop and start control Driver door courtesy switch ON signal is input Driver door is closed Always
Engine Hood Engine hood is opened before engine stop by stop and start control Engine hood switch OFF signal is input Engine hood is closed Always
Seat Belt Driver seat belt is not fastened before engine stop by engine stop and start control Driver seat belt buckle switch OFF signal is input Driver seat belt is fastened Always
Ambient Temperature Ambient temperature -6°C (21.2°F) or less - Ambient temperature -5°C (23°F) or higher Always
Power Source Battery voltage drops below 6.6 V at engine start Battery charge is insufficient or battery has deteriorated Battery is charged or replaced Every time the engine is started
Battery temperature is -15°C (5°F) or less or 75°C (167°F) or higher
(At low temperatures: Engine restarting is not assured
At high temperatures: For battery protection)
Depends on Ambient temperature An appropriate battery temperature is reached Always
Battery integrated current* value is:
1.

Less than 0 A-sec: After engine start by ignition switch operation

2.

Either of the following integrated current conditions is met:

·

-6451 A-sec or less: The battery charge is sufficient and the battery temperature is -1°C (30.2°F) or higher and below 70°C (158°F)

·

-1152 A-sec or less: The battery charge is insufficient or the battery temperature is below -1°C (30.2°F) or 70°C (158°F) or higher



·

Heavy electrical load

·

High stop and start rate (Time that engine stopped by stop and start control is long)


Battery integrated current* value is more than a certain level.
1.

0 A-sec or higher: After engine start by ignition switch operation

2.

Either of the following integrated current conditions is met:

·

-5299 A-sec or higher: The battery charge is sufficient and the battery temperature is -1°C (30.2°F) or higher and below 70°C (158°F)

·

0 A-sec or higher: The battery charge is insufficient or the battery temperature is below -1°C (30.2°F) or 70°C (158°F) or higher



Always
During refresh charge A refresh charge of 30 minutes or more is performed after every 20 hours of driving Refresh charge is completed Always
Idling stop rate 40% or higher - Idling stop rate 24% or less Always
Engine is started with the engine hood open (for jump starting) - Ignition switch is turned off Every time the engine is started

HINT:
·

*: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value

·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.




WARNING CONTROL


If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.

Operation Warning Control
The driver door is opened while the shift lever is in neutral The engine starts
The driver seat belt is unfastened The engine starts
The engine hood opened The engine changes to "stalled"
The shift lever is operated without depressing the clutch pedal The buzzer sounds and stop and start indicator light blinks (engine will not start)


WARNING INDICATOR AND BUZZER OPERATION


A287227C01
0.677,0.271 1.031,0.583 0.354,0.313 10 *a 0.677,1.729 1.031,2.042 0.354,0.313 10 *b
*a Stop and Start Indicator Light
(Green)
*b Stop and Start Cancel Indicator Light
(Orange)


The driver is informed of the system control status and warnings by the stop and start indicator light, stop and start cancel indicator light and the buzzer.

Stop and Start Indicator and Buzzer Operation
Item Condition Stop and start indicator light
(Green)
Stop and start cancel indicator light
(Orange)
Buzzer
For 3 seconds after the ignition switch to ON Normal operation Comes on Comes on Does not sound
During stop and start control operation (engine is stopped) Normal operation Comes on Does not come on Does not sound
The shift lever is operated without depressing the clutch pedal The blinking interval is 0.15 seconds. Does not come on Sounds
Control is prohibited by the stop and start cancel switch Normal operation Does not come on Comes on Does not sound
Diagnostic trouble code Any DTCs are stored Does not come on The blinking interval is 0.5 seconds. Does not sound
Starter life The number of times the starter has been operated exceeds its limit Does not come on The blinking interval is 0.5 seconds. Does not sound


STOP AND START SYSTEM OPERATION


Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunctions in the stop and start system.

Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
IGSW circuit Open P2531
·

IG Switch

·

IG SW Abnoml


Stop and start control prohibited Wire harness or connector
+B circuit Open - Data List cannot be checked because power is not supplied to the engine stop and start ECU Stop and start control prohibited Wire harness or connector
TMN (neutral position switch) circuit Stuck on P1780
·

Neutral Switch

·

N position Switch

·

N Position Voltage Status


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Neutral position switch


Stuck off P1780
·

Neutral Switch

·

N position Switch

·

N Position Voltage Status


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


CLL (clutch start switch assembly (for lower)) circuit Stuck on P1862
·

Clutch Lower SW

·

Clutch SW Signal Abnoml

·

N/Clutch Lower SW Abnoml


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Clutch start switch assembly (for lower)

·

Clutch switch assembly (for upper)


Stuck off -
·

Clutch Lower SW

·

N/Clutch Lower SW Abnoml


Stop and start control prohibited
CLU (clutch switch assembly (for upper)) circuit Stuck on P1862
·

Clutch Upper SW

·

Clutch SW Signal Abnoml

·

N/Clutch Upper SW Abnoml


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Stuck off -
·

Clutch Upper SW

·

N/Clutch Upper SW Abnoml


Stop and start control prohibited
BNT1 (hood lock switch) circuit Stuck on - Hood Courtesy Switch The engine does not stall when the engine hood is opened with the shift lever in neutral while the engine is stopped by stop and start control
·

Wire harness or connector

·

Hood lock switch assembly


Stuck off - Hood Courtesy Switch Stop and start control prohibited despite the engine hood being closed
BRVC/PB/BRE2 (vacuum sensor) circuit Open P1540
·

Brk Boost Sen Abnoml 1

·

Brk Boost Sen Abnoml 2

·

Brk Boost Sen Abnoml 3


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Vacuum sensor assembly

·

Brake booster assembly

·

Check valve to connector tube hose


Shorted P1540
Remains at intermediate value P1541
ECAN (stop and start cancel switch) circuit Stuck on - Cancel Switch Stop and start control prohibited
·

Wire harness or connector

·

Stop and start system cancel switch (combination switch assembly)


Stuck off - Cancel Switch Stop and start control cannot be canceled by pressing the stop and start system cancel switch (combination switch assembly)
STA circuit Over-current P0617
·

Starter Relay Overcurrent

·

Starter Circuit Abnoml

·

Starter Circuit Open


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU


Stuck on P1644
·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU


Stuck off P1644
BBC (backup boost converter) circuit Over-current B22C0
·

State of BBC

·

BBC Abnoml

·

BBC Overcurrent

·

BBC Check Result


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery

·

ECUs and sensors connected to BO1 and IGO1


·

Open

·

Shorted

·

Internal circuit malfunction

·

Battery


P323B
·

State of BBC

·

BBC Duty

·

BBC Thermistor

·

BBC Abnoml

·

BBC Over Heat

·

BBC Power Low


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery


VB- circuit Open P0560 VB Voltage Low
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Engine stop and start ECU


ECU inner circuit Malfunction P0607 -
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
Monitoring CPU circuit Malfunction P060A State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
EEPROM Malfunction P062F EEPROM
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
Sensor power source circuit Malfunction P0641 State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU

Effects on Vehicle due to Related System Malfunctions
Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
ECD system MIL illuminated DTCs for ECD system output Oper Permission (ECM) Stop and start control prohibited ECD system
Abnormal NE signal P0335
·

NE Sensor Circuit Open 2

·

Crank Pos Sen Abnoml 3


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

ECD system (crankshaft position sensor circuit)

·

Wire harness or connector


Battery current sensor (generator control ECU assembly) malfunction P0516
P0517
P1550
P1551
P1552
·

Battery Fluid Temperature

·

Integrated Current


Stop and start control prohibited Charging system
Brake control system Brake control system - ABS Running Stop and start control prohibited -
Malfunction in wheel speed sensor Brake control system DTCs output
·

Vehicle Spd1 (ABS/VSC)

·

Wheel Speed Malfunction


Stop and start control prohibited
·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

Vehicle speed sensor


Power steering system Malfunction in power steering system EPS assist current value invalid
·

EPS Load

·

Comm Err with EPS


Stop and start control prohibited
·

Power steering ECU assembly

·

Torque sensor


Seat belt warning system Malfunction in seat belt warning system - Oper Permission (Driver Side Buckle SW)
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)


·

Front seat inner belt assembly (Driver side)

·

Wire harness or connector


Driver door courtesy light switch circuit Malfunction in driver door courtesy light switch circuit - D Courtesy Switch
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)


·

Front door courtesy light switch assembly (Driver side)

·

Driver door courtesy light switch circuit


Air conditioning system Malfunction in ambient temperature sensor Air conditioning system DTCs output Ambient Temp Sensor Stop and start control prohibited Ambient temp sensor circuit
Brake vacuum Brake booster vacuum drops -
·

Brake Boost Pressure

·

Brake Negative Pressure

·

Brk Boost Sen Abnoml 1

·

Brk Boost Sen Abnoml 2

·

Brk Boost Sen Abnoml 3


Stop and start control prohibited
·

Brake booster assembly vacuum

·

Brake booster assembly

·

Vacuum sensor assembly

·

Check valve to connector tube hose


Power source Backup boost converter malfunction P323B
·

State of BBC

·

BBC Duty

·

BBC Thermistor

·

BBC Abnoml

·

BBC Over Heat

·

BBC Power Low


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery


Charging system malfunction - Alternator Status Stop and start control prohibited Charging system
Low voltage P0562 Battery Abnoml
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Battery

·

Relay


Number of starter operations Exceeds the specified limit P1545 Starter Count Abnoml
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Starter assembly replacement is required.

·

ST relay replacement is required.

·

Fuse replacement is required.


Starter signal malfunction Signal does not match with the starter switch P1545 -
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Engine stop and start ECU


Jump start Engine started with the engine hood open - Eng Start Reg (Engine Hood Open) Stop and start control prohibited
(recovers when the ignition switch is turned off)
·

Check for a history of roadside service or jump start due to dead battery

·

Engine hood courtesy switch (hood lock assembly)


CAN communication Communication interrupted U0100
U0121
U0131
U0140
U0151
U0155*
U0164
-
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks*


·

Applicable wire harness or connector

·

Applicable ECU



HINT:

*: The stop and start cancel indicator light does not blink when a communication error with the combination meter assembly occurs.