Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) L

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  PRECAUTION  


IGNITION SWITCH EXPRESSION


HINT:

The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.


Expression Ignition Switch
(Position)
Engine Switch
(Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)


CAN COMMUNICATION SYSTEM TROUBLESHOOTING


a.

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING



PRECAUTIONS FOR STEERING SYSTEM HANDLING


a.

Be careful when replacing parts. Incorrect replacement could affect the performance of the steering system and result in hazardous driving.



PRECAUTIONS FOR SRS AIRBAG SYSTEM HANDLING


a.

This vehicle is equipped with a Supplemental Restraint System (SRS) which includes parts such as airbags for the driver and front passenger. Failure to carry out service operations in the correct sequence could cause unexpected SRS deployment during servicing and may cause a serious accident. Before servicing (removal/installation, inspection and replacement of parts), be sure to read precaution for SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION



BUS WIRE REPAIR


a.
E120441

After repairing the bus wire with solder, wrap the repaired part with vinyl tape.

NOTICE:
·

The CANH bus wire and CANL bus wire must be installed together.

·

When installing the CAN bus wires, make sure to twist them.

·

CAN bus wires are likely to be influenced by noise if the bus wires are not twisted together.

·

Leave approximately 80 mm (3.15 in.) loose in the twisted wires around the connectors.




b.
E134624C02
1.497,0.511 1.669,0.678 0.172,0.167 10 *1 1.707,0.605 1.85,0.605 1.85,0.605 2.053,1.03 false
*1 By-pass Wire


Do not use by-pass wiring between the connectors.

NOTICE:

The protective effect of the twisted wire harness will be lost if bypass wiring is used.




CONNECTOR HANDLING


a.
E120443C02
1.802,1.219 1.323,1.604 1.323,1.604 1.542,1.542 true 1.073,1.521 1.281,1.688 0.208,0.167 10 *1
*1 Tester Probe


When inserting probes into a connector, insert them from the rear of the connector.


b.
E120444C02
1.448,0.917 1.875,0.594 1.875,0.594 1.531,1.302 true 1.875,0.594 1.958,0.594 false 1.979,0.51 2.167,0.677 0.188,0.167 10 *1
*1 Repair Wire


Use a repair wire to check the connector if it is impossible to check resistance from the rear of the connector.



PRECAUTIONS FOR INSPECTING OR REPLACING CAN JUNCTION CONNECTOR


a.

If the CAN junction connector is removed from the vehicle for inspection or replacement, make sure to install the CAN junction connector and all wire harnesses to their original locations with tape and the clamps.



PRECAUTIONS WHEN REPLACING A GATEWAY FUNCTION EQUIPPED ECU (SUB BUS MONITOR ECU) WITH A USED ONE FROM ANOTHER VEHICLE


a.

When a gateway function equipped ECU (main body ECU) that was previously installed on another vehicle is used as a replacement part, it is necessary to initialize the connection information stored in the ECU.

NOTICE:

If the connection information stored in a gateway function equipped ECU that was previously installed on another vehicle is different from the actual ECUs and sensors connected to the corresponding bus, communication DTCs will be detected.


HINT:

When an ECU is replaced with one from a vehicle with the same options and specifications (the same connections to the corresponding bus), initialization of ECU connection information is not necessary.



b.

Initialize the connection information of a gateway function equipped ECU (sub bus monitor ECU)


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch is ON.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Main Body / Utility.


g.

Select Initialization from Utility to initialize the ECU.

Body Electrical > Main Body > Utility
Tester Display
Initialization
50005 123 207


PRECAUTIONS FOR WHEN GATEWAY FUNCTION EQUIPPED ECU (SUB BUS MONITOR ECU) DETECTS COMMUNICATION DTCS FOR ECUS NOT CONNECTED TO THE ECU


a.

Refer to Precautions When Replacing a Gateway Function Equipped ECU (Sub Bus Monitor ECU) with a Used One from Another Vehicle and initialize the connection information of the ECU.


b.

Clear the DTCs and check that no DTCs are output.