The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the sub bus 1.
When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the sub bus 1, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the sub bus 1. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the sub bus 1 when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the sub bus 1, the main body ECU (multiplex network body ECU) determines that a malfunction exists.
If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U1002 | Lost Communication with Gateway Module | Lost communication with the gateway module. | ·
Sub bus 1 circuit ·
Main body ECU (multiplex network body ECU) CAN main wire or connector ·
Multiplex network door ECU CAN branch wire or connector ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Multiplex network door ECU ·
No. 4 CAN junction connector* ·
No. 5 CAN junction connector ·
No. 6 CAN junction connector |
Main body ECU (multiplex network body ECU) |
*: for Power Seat
For vehicles with a power back door system.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
| *a | Component with harness connected
(No. 6 CAN Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Resistance: Malfunction |
|---|---|---|---|
| N31-3 (CANH) - N31-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 53 Ω: Short in line |
| N31-3 (CANH) - N31-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Higher than 70 Ω: Open in CAN main bus line |
| N31-3 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| N31-2 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: +B short |
| N31-3 (CANH) - N31-1 (E) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| N31-2 (CANL) - N31-1 (E) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Ground short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG
- Open in CAN main wire |
B |
| NG
- Short in CAN bus wire |
C |
| NG
- +B short - Ground short |
D |
A
B
C
D
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from main body ECU (multiplex network body ECU) | A |
| Other DTC is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSTIC TROUBLE CODE CHART
| *a | Rear view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to No. 6 CAN Junction Connector |
| *c | to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat) |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N32-9 (CANH) - N32-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| N32-10 (CANH) - N32-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to No. 6 CAN junction connector CAN main wire) | B |
| NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) | C |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) | D |
A
B
C
D
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 6 CAN Junction Connector) |
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N31-3 (CANH) - N31-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to No. 5 CAN Junction Connector |
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N30-1 (CANH) - N30-7 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| N30-2 (CANH) - N30-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) | B |
| NG (to No. 5 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the N30 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-9 (CANP) - G79-10 (CANN) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-9 (CANP) - G79-10 (CANN) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to Multiplex Network Door ECU |
| *c | to No. 6 CAN Junction Connector |
| *d | to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat) |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N32-8 (CANH) - N32-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N32-9 (CANH) - N32-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| N32-10 (CANH) - N32-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to multiplex network door ECU CAN branch wire) | B |
| NG (to No. 6 CAN junction connector CAN main wire) | C |
| NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) | D |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) | E |
A
B
C
D
E
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U18-13 (CANP) - U18-14 (CANN) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 6 CAN Junction Connector) |
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N31-3 (CANH) - N31-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to No. 5 CAN Junction Connector |
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N30-1 (CANH) - N30-7 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| N30-2 (CANH) - N30-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) | B |
| NG (to No. 5 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the N30 No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-9 (CANP) - G79-10 (CANN) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 5 CAN junction connector.
| *a | Rear view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Multiplex Network Door ECU | *d | to No. 6 CAN Junction Connector |
| *e | to No. 4 CAN Junction Connector (for Power Seat) or Main Body ECU (Multiplex Network Body ECU) (except Power Seat) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose | Connected to |
|---|---|---|---|---|
|
*1: for Power Seat *2: except Power Seat |
||||
| N32-8 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANH ground short | Multiplex network door ECU |
| N32-19 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| N32-8 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANH +B short | |
| N32-19 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANL +B short | |
| N32-9 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANH ground short | No. 6 CAN junction connector |
| N32-20 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| N32-9 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANH +B short | |
| N32-20 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANL +B short | |
| N32-10 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANH ground short | ·
No. 4 CAN junction connector*1 ·
Main body ECU (multiplex network body ECU)*2 |
| N32-21 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| N32-10 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANH +B short | |
| N32-21 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANL +B short | |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to multiplex network door ECU CAN branch wire) | B |
| NG (to No. 6 CAN junction connector CAN main wire) | C |
| NG (to No. 4 CAN junction connector CAN main wire) (for Power Seat) | D |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) (except Power Seat) | E |
A
B
C
D
E
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
| *b | Front view of DLC3 |
Disconnect the multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U18-13 (CANP) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| U18-14 (CANN) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| U18-13 (CANP) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| U18-14 (CANN) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N31-3 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N31-2 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N31-3 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N31-2 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to No. 5 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Purpose | Connected to |
|---|---|---|---|---|
| N30-1 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANH ground short | Main body ECU (multiplex network body ECU) |
| N30-7 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| N30-1 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANH +B short | |
| N30-7 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANL +B short | |
| N30-2 (CANH) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANH ground short | No. 5 CAN junction connector |
| N30-8 (CANL) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inspection for CANL ground short | |
| N30-2 (CANH) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANH +B short | |
| N30-8 (CANL) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Inspection for CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to main body ECU [multiplex network body ECU] CAN main wire) | B |
| NG (to No. 5 CAN junction connector CAN main wire) | C |
A
B
C
Reconnect the N30 No. 4 CAN junction connector.
| Result |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
| *b | Front view of DLC3 |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-9 (CANP) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G79-10 (CANN) - G14-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G79-9 (CANP) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G79-10 (CANN) - G14-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the N32 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT