The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning switch (on/off), air conditioning refrigerant pressure, engine speed and vehicle speed signals.
The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.
Refer to the System Diagram.
Click hereEngine / Hybrid System>1AD-FTV COOLING>COOLING FAN SYSTEM>SYSTEM DIAGRAM
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).
After replacing the ECM, the new ECM needs initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.
| Tester Display |
|---|
| Control the Electric Cooling Fan |
Check the operation of the cooling fan while operating it using the GTS.
| GTS Operation | Fan Operation |
|---|---|
| ON | Cooling fans operate |
| OFF | Cooling fans stop |
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Disconnect the A61 ECM connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-21 (FANH) - Body ground | Ignition switch ON | 11 to 14 V |
| A61-22 (FANL) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the A61 ECM connector.
| Result |
|---|
| OK |
| NG |
OK
NG
| *1 | FAN No. 1 Relay |
| *2 | FAN No. 3 Relay |
| *a | No. 2 Engine Room Relay Block and Junction Block Assembly |
Remove the FAN No. 1 relay and FAN No. 3 relay from the No. 2 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FAN No. 1 relay) - Body ground | Always | 11 to 14 V |
| 3 (FAN No. 3 relay) - Body ground | Always | 11 to 14 V |
Reinstall the FAN No. 1 relay and FAN No. 3 relay.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 1 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 2 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 3 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the FAN No. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (FAN No. 2 relay) - Body ground | Always | Below 1 Ω |
Reinstall the FAN No. 2 relay.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the cooling fan motor.
Click hereEngine / Hybrid System>1AD-FTV COOLING>COOLING FAN MOTOR>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A52 cooling fan motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-1 - Body ground | Always | Below 1 Ω |
Reconnect the A52 cooling fan motor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A52 cooling fan motor connector.
Remove the FAN No. 1 relay and FAN No. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-2 - 5 (FAN No. 1 relay) | Always | Below 1 Ω |
| A52-2 or 5 (FAN No. 1 relay) - Body ground | 10 kΩ or higher | |
| A52-2 - 4 (FAN No. 2 relay) | Below 1 Ω | |
| A52-2 or 4 (FAN No. 2 relay) - Body ground | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
Reconnect the A52 cooling fan motor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 2 cooling fan motor.
Click hereEngine / Hybrid System>1AD-FTV COOLING>COOLING FAN MOTOR>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A51 No. 2 cooling fan motor connector.
Remove the FAN No. 2 relay and FAN No. 3 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Condition |
|---|---|---|
| A51-1 - 3 (FAN No. 2 relay) | Always | Below 1 Ω |
| A51-1 or 3 (FAN No. 2 relay) - Body ground | 10 kΩ or higher | |
| A51-2 - 5 (FAN No. 3 relay) | Below 1 Ω | |
| A51-2 or 5 (FAN No. 3 relay) - Body ground | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reinstall the FAN No. 2 relay and FAN No. 3 relay.
Reconnect the A51 No. 2 cooling fan motor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the FAN No. 1 relay and FAN No. 2 relay from the No. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (FAN No. 1 relay) - 1 (FAN No. 2 relay) | Always | Below 1 Ω |
| 1 (FAN No. 1 relay) or 1 (FAN No. 2 relay) - Body ground | 10 kΩ or higher | |
| 2 (FAN No. 1 relay) - 2 (FAN No. 2 relay) | Below 1 Ω | |
| 2 (FAN No. 1 relay) or 2 (FAN No. 2 relay) - Body ground | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 1 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 2 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 3 relay.
Click hereEngine / Hybrid System>1AD-FTV COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay from the No. 2 engine room relay block and junction block assembly.
Disconnect the A61 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FAN No. 1 relay) - A61-21 (FANH) | Always | Below 1 Ω |
| 2 (FAN No. 1 relay) or A61-21 (FANH) - Body ground | 10 kΩ or higher | |
| 2 (FAN No. 2 relay) - A61-21 (FANH) | Below 1 Ω | |
| 2 (FAN No. 2 relay) or A61-21 (FANH) - Body ground | 10 kΩ or higher | |
| 2 (FAN No. 3 relay) - A61-22 (FANL) | Below 1 Ω | |
| 2 (FAN No. 3 relay) or A61-22 (FANL) - Body ground | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reconnect the A61 ECM connector.
Reinstall the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay.
| Result |
|---|
| OK |
| NG |
OK
NG