Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2WD) › 2012.12–2014.10
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050235 FRONT DRIVE SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2WD)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 43448G 1.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

C127644
0.094,0.135 0.406,0.333 0.313,0.198 10 *A 0.094,2.24 0.406,2.438 0.313,0.198 10 *B
*A for One Touch Type
*B for Claw Engagement Type


a.

for One Touch Type:

Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


b.

for Claw Engagement Type:

Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


Hide 43448E 2.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43448F 3.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.


Hide 43448C 4.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 5.DISCONNECT FRONT AXLE INBOARD JOINT BOOT

a.

Disconnect the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 43040 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

C127646C04
2.167,0.396 2.167,0.25 2.167,0.25 1.083,0.25 true 1.833,0.802 1.833,0.25 true 0.875,0.167 1.167,0.354 0.292,0.188 10 *a
*a Matchmark


a.

Remove any old grease from the front drive inboard joint assembly LH.


b.

Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.


d.
C127648

Using a snap ring expander, remove the snap ring.


e.
C127649C03
2.677,0.76 2.677,1.542 2.677,1.542 2.938,1.542 true 2.802,0.844 2.802,1.531 true 3,1.438 3.313,1.635 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



f.

Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

NOTICE:

Do not tap the rollers.



g.

Remove the front axle inboard joint boot.


Hide 43030 7.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43474G 8.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ Drive Shaft Damper)

C127651C01
0.063,0.031 0.271,0.198 0.208,0.167 10 *A 0.073,2.292 0.302,2.469 0.229,0.177 10 *B
*A for One Touch Type
*B for Claw Engagement Type


a.

for One Touch Type:

Using a screwdriver, remove the front drive shaft damper clamp LH as shown in the illustration.


b.

for Claw Engagement Type:

Using needle-nose pliers, remove the front drive shaft damper clamp LH as shown in the illustration.


Hide 43474F 9.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ Drive Shaft Damper)

HINT:

Use the same procedure described for the LH side.


Hide 43474E 10.REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)

a.

Remove the front drive shaft damper LH from the front drive outboard joint shaft assembly LH.


Hide 43474D 11.REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ Drive Shaft Damper)

HINT:

Use the same procedure described for the LH side.


Hide 43447F 12.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

C127653

a.

Using a screwdriver, remove the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.


Hide 43447D 13.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43447E 14.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.


Hide 43447C 15.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 16.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot from the front drive outboard joint shaft assembly.


b.

Remove any old grease from the front drive outboard joint shaft assembly.


Hide 41336E 17.REMOVE FRONT DRIVE SHAFT DUST COVER LH

C127659N02
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

a.

Using SST and a press, remove the front drive shaft dust cover LH.

SST
09950-00020  

NOTICE:

Be careful not to drop the front drive inboard joint assembly LH.



Hide 41336D 18.REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 43045 19.REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY

a.

w/ Drive Shaft Bearing Case:

i.
C127662

Using a screwdriver, remove the bearing case snap ring from the drive shaft bearing case sub-assembly.


ii.
C127663

Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly RH.

NOTICE:

Be careful not to drop the front drive inboard joint assembly RH.




Hide 43458 20.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
C127664N02
1.219,1.5 1.021,1.323 1.021,1.323 0.625,1.323 true 0.281,1.24 0.573,1.385 0.292,0.146 10 SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

SST
09950-00020  

NOTICE:

Be careful not to drop the front drive inboard joint assembly RH.



Hide 43410C 21.REMOVE FRONT DRIVE SHAFT BEARING

C127665

a.

Using a snap ring expander, remove the snap ring.


b.
C127666N03
2.615,0.906 2.417,0.906 2.417,0.906 2.177,1.479 true 2.698,0.833 3.01,0.99 0.313,0.156 10 SST

Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

SST
09527-10011  

NOTICE:

Be careful not to drop the front drive inboard joint assembly RH.