Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050237 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42347F 1.REMOVE REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

C129490

a.

Using needle-nose pliers, remove the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.


Hide 42347D 2.REMOVE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the rear No. 2 drive shaft inboard joint boot clamp LH.


Hide 3.DISCONNECT INBOARD JOINT BOOT

a.

Disconnect the inboard joint boot from the rear drive shaft inboard joint assembly.


Hide 42360D 4.REMOVE REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

C129505
1.333,0.25 1.167,0.25 false 1.76,1 1.333,0.25 1.333,0.25 2.083,0.594 true 0.99,0.146 1.708,0.292 0.719,0.146 10 *a
*a Matchmark


a.

Remove any old grease from the rear drive shaft inboard joint assembly LH.


b.

Put matchmarks on the rear drive shaft inboard joint assembly LH and rear drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the rear drive shaft inboard joint assembly LH from the rear drive outboard joint shaft assembly LH.


d.
C127648

Using a snap ring expander, remove the snap ring.


e.
C129492
1.49,1.219 1.333,1.833 1.333,1.833 2.083,1.583 true 1.333,1.833 1.167,1.833 false 0.99,1.729 1.719,1.885 0.729,0.156 10 *a
*a Matchmark


Put matchmarks on the rear drive outboard joint shaft assembly LH and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



f.

Using a brass bar and hammer, remove the tripod joint from the rear drive outboard joint shaft assembly LH.

NOTICE:

Do not tap the rollers.



g.

Remove the inboard joint boot.


Hide 42346F 5.REMOVE REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

C277140

a.

Using a screwdriver, remove the rear No. 2 drive shaft outboard joint boot clamp LH as shown in the illustration.


Hide 42346D 6.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

C277139

a.

Using pliers, remove the rear drive shaft outboard joint boot clamp LH as shown in the illustration.


Hide 7.REMOVE OUTBOARD JOINT BOOT

a.

Remove the outboard joint boot from the rear drive outboard joint shaft assembly LH.


b.

Remove any old grease from the rear drive outboard joint shaft assembly LH.


Hide 41336K 8.REMOVE REAR DRIVE SHAFT DUST COVER LH

C127659N02
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

a.

Using SST and a press, remove the rear drive shaft dust cover LH.

SST
09950-00020  

NOTICE:

Be careful not to drop the rear drive shaft inboard joint assembly LH.