Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for LHD)
RM3090E _52 Drivetrain _008754 CLUTCH _0050263 CLUTCH PEDAL(for LHD) A

CLUTCH  CLUTCH PEDAL(for LHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly


Hide 31301P 2.INSTALL CLUTCH PEDAL TURNOVER BUSH

C279726C01
2.417,0.063 2.594,0.198 0.177,0.135 10 false .
V100135

MP Grease


a.

Apply MP grease to the contact surface of the clutch pedal turnover bush.


b.

Install the clutch pedal turnover bush.


c.

Install the 2 clutch pedal cushions to the clutch pedal sub-assembly.


Hide 31324A 3.INSTALL CLUTCH PEDAL SHAFT COLLAR

C279724C01
2.833,0.49 2.896,0.396 false
V100135

MP Grease


a.

Apply MP grease to both sides of a clutch pedal shaft collar and 2 new bushes.


b.

Install the clutch pedal shaft collar.


c.

Install the 2 bushes.


Hide 31353 4.INSTALL CLUTCH PEDAL SPRING HOLDER

C279723C01
0.938,0.854 1.021,0.958 0.083,0.104 10 false .
V100135

MP Grease


a.

Apply MP grease to the contact surface of the clutch pedal spring holder.


b.

Install the clutch pedal spring holder.


Hide 31301 5.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

HINT:

Install the bolt from the right side of the vehicle.



Hide 31395A 6.INSTALL NO. 1 PEDAL SPRING HOOK

C279727C01
0.292,0.427 0.448,0.625 0.156,0.198 10 false .
V100135

MP Grease


a.

Apply MP grease to the contact surface of the No. 1 pedal spring hook.


b.

Install the No. 1 pedal spring hook.


Hide 7.INSTALL CLUTCH PEDAL SPRING WITH HOOK

a.

Apply MP grease to the contact surface of the clutch pedal spring with hook.


b.

Install the clutch pedal spring with hook to the No. 1 pedal spring hook.


c.
C125483C01
1.5,0.323 1.656,0.521 0.156,0.198 10 false .
V100135

MP Grease


Install the clutch pedal spring with hook to the clutch pedal sub-assembly.


Hide 31394A 8.INSTALL CLUTCH PEDAL SPRING

C279722C01
1.198,0.938 1.354,1.135 0.156,0.198 10 false .
V100135

MP Grease


a.

Apply MP grease to the contact surface of the clutch pedal spring.


b.

Install the clutch pedal spring.


Hide 84520 9.INSTALL CLUTCH START SWITCH ASSEMBLY

Hide 88280A 10.INSTALL CLUTCH SWITCH ASSEMBLY

Hide 55107A 11.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

C278063N01
0.875,0.51 1.031,0.708 0.156,0.198 10 false A 2.167,0.75 2.323,0.948 0.156,0.198 10 false A 2.01,0.229 2.167,0.427 0.156,0.198 10 false B

a.

Install the clutch pedal support sub-assembly.


b.

Install the bolt and 2 nuts.

Torque:
for nut A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)


c.

Connect the 2 connectors and clamp.


Hide 31453A 12.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

C279741C01
2.229,0.354 2.406,0.552 0.177,0.198 10 false . 1.219,2.229 1.323,2.313 0.104,0.083 10 false .
V100135

MP grease


a.

Apply Mp grease to the contact surface of the clutch master cylinder push rod clevis with hole pin.


b.

Connect the clevis to the clutch pedal assembly with the clutch master cylinder push rod clevis with hole pin.

HINT:

install the clutch master cylinder push rod clevis with hole pin from the right side of the vehicle.



c.

Install a new clip to the clutch master cylinder push rod clevis with hole pin.


Hide 55302A 13.INSTALL UPPER INSTRUMENT PANEL

Hide 73900 14.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432B 15.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 55606 16.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 31301 17.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY