Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) Y

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use this procedure to troubleshoot the immobiliser system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:



What Vehicle model, system name
When Date, time, occurrence frequency
Where Whether the problem occurs at a specific location.
Under what conditions? Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine was running.
How did it happen? Problem symptoms

Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CRANK ENGINE FOR MORE THAN 10 SECONDS
4.CRANK ENGINE FOR MORE THAN 10 SECONDS
Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC* (ECM AND TELEPHONE TRANSCEIVER ASSEMBLY)
5.CHECK FOR DTC* (ECM AND TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 61
Body Electrical > Telematics > Trouble Codes
50001 233
Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.



Result:
Proceed to
DTCs are not output
SFI system DTCs are output (for 2AR-FE)
SFI system DTCs are output (for 3ZR-FAE)
SFI system DTCs are output (for 3ZR-FE)
ECD system DTCs are output (for 1AD-FTV)
ECD system DTCs are output (for 2AD-CCo)
ECD system DTCs are output (for 2AD-DPF)
ECD system DTCs are output (for 2AD-FHV)
Blocking system DTCs are output (w/ Blocking System)
Immobiliser system DTCs are output



DTCs are not output

6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)

SFI system DTCs are output (for 2AR-FE)

SFI system DTCs are output (for 3ZR-FAE)

SFI system DTCs are output (for 3ZR-FE)

ECD system DTCs are output (for 1AD-FTV)

ECD system DTCs are output (for 2AD-CCo)

ECD system DTCs are output (for 2AD-DPF)

ECD system DTCs are output (for 2AD-FHV)

Blocking system DTCs are output (w/ Blocking System)

Immobiliser system DTCs are output

6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.



Result:
Proceed to
DTCs are not output
Immobiliser system DTCs are output



DTCs are not output

7.PROBLEM SYMPTOMS TABLE

Immobiliser system DTCs are output

7.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table



Fault is not listed in problem symptoms table

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
HINT:

If the transponder key ECU assembly, ECM, or key is replaced, refer to the Service Bulletin.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC*
10.CHECK FOR DTC*
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.



Result:
Proceed to
DTCs are not output
Immobiliser system DTCs are output



DTCs are not output

END

Immobiliser system DTCs are output