Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2793  Transponder Chip Malfunction  B2794  Unmatched Encryption Code  B2797  Communication Malfunction No. 1  B2798  Communication Malfunction No. 2  


DESCRIPTION

·

DTC B2793 is stored when a malfunction is found in the key during key ID code registration or a key ID code is not registered normally. Replace the key if key ID code registration cannot be performed normally and this DTC is output.

·

DTC B2794 is stored when a key with an incomplete key ID code is inserted into the ignition key cylinder.

·

DTC B2797 is stored when a key with a BCC malfunction is inserted into the ignition key cylinder.

·

DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2793 Transponder Chip Malfunction A transponder chip malfunction (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder


B2794 Unmatched Encryption Code A key with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder


B2797 Communication Malfunction No. 1 A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder


B2798 Communication Malfunction No. 2 Key ID code identification cannot be completed within the specified time (1 trip detection logic*).
·

Key

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2793 -
B2794 -
B2797 -
B2798 -

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:
·

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

·

If DTC B2793, B2794, B2797, or B2798 is stored, clear the DTCs before checking the next key.




Result:
Proceed to
DTC B2793, B2794, B2797 and B2798 are not output
DTCs are output for all of the keys
DTCs are output for any of the keys



DTC B2793, B2794, B2797 and B2798 are not output

DTCs are output for all of the keys

3.CHECK CONNECTION OF CONNECTOR

DTCs are output for any of the keys

REPLACE KEY FOR WHICH DTC WAS OUTPUT

3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.


b.

Check that the engine starts with the key.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

4.CHECK TRANSPONDER KEY COIL
4.CHECK TRANSPONDER KEY COIL
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260


c.

Check that the engine starts with the key.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY