Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2795  Unmatched Key Code  


DESCRIPTION

This DTC is stored when a key with a different vehicle serial number is inserted into the ignition key cylinder.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2795 Unmatched Key Code A key with a different vehicle serial number is inserted into the ignition key cylinder (1 trip detection logic*).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2795 -

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:
·

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

·

If DTC B2795 is stored, check for DTCs with the next key after clearing the DTCs.




Result:
Proceed to
DTC B2795 is not output
DTC B2795 is output for all of the keys
DTC B2795 is output for any of the keys



DTC B2795 is not output

DTC B2795 is output for all of the keys

REPLACE TRANSPONDER KEY ECU ASSEMBLY

DTC B2795 is output for any of the keys

3.CHECK OPERATION (IGNITION SWITCH)
3.CHECK OPERATION (IGNITION SWITCH)
a.

Check that the ignition switch can be turned to ON using the key for which the DTC was stored.

OK:

Ignition switch can be turned to ON using the key (for which the DTC was stored).



Result:
Proceed to
OK
NG



OK

4.REREGISTRATION

NG

REPLACE KEY FOR WHICH DTC WAS OUTPUT

4.REREGISTRATION
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

b.

Reregister the key ID code with the transponder key ECU assembly.

HINT:

Refer to the Service Bulletin.


OK:

Registration procedure can be completed.



Result:
Proceed to
OK
NG



OK

END (KEY REGISTRATION FAILURE)

NG

REPLACE KEY FOR WHICH DTC WAS OUTPUT