Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B271008E17
4.49,1.115 4.802,1.271 0.313,0.156 10 false G88 4.448,2.958 4.927,3.135 0.479,0.177 10 false G79 4.49,1.281 5.906,1.823 1.417,0.542 10 false Transponder Key ECU Assembly 4.448,3.115 6.094,3.604 1.646,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 1.021,1.115 1.417,1.354 0.396,0.24 10 false G43 1.01,1.271 2.938,1.875 1.927,0.604 10 false Security Indicator Light (Telltale Light Assembly) 4.771,0.594 5.031,0.76 0.26,0.167 10 false IND 4.771,2.5 5.031,2.667 0.26,0.167 10 false IND 4.573,0.49 4.729,0.646 0.156,0.156 10 false 8 4.51,2.375 4.74,2.635 0.229,0.26 10 false 22 2.74,0.49 3.01,0.646 0.271,0.156 10 false 21 1.469,0.49 1.656,0.646 0.188,0.156 10 false 13 3.604,1.521 3.802,1.698 0.198,0.177 10 false * 0.75,2.958 2.646,3.135 1.896,0.177 10 false *: w/ Theft Deterrent System 1.719,0.604 2.333,0.802 0.615,0.198 10 false E 2.458,0.604 3.073,0.802 0.615,0.198 10 false LP

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to the Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Proceed to
w/o Theft Deterrent System
w/ Theft Deterrent System



w/o Theft Deterrent System

2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)

w/ Theft Deterrent System

5.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the G43 security indicator light (telltale light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G43-21 (LP) - G88-8 (IND) Always Below 1 Ω
G43-21 (LP) - Body ground Always 10 kΩ or higher
G88-8 (IND) - Body ground Always 10 kΩ or higher
G43-13 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the G88 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G43-21 (LP) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19

Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D



A

6.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION

B

7.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU)

D

9.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU OR TRANSPONDER KEY ECU AND BODY GROUND)
6.CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on.



Result:
Proceed to
Both *1 and *2 are OK
*1 is NG (*2 is OK)
*2 is NG (*1 is OK) (for LHD)
*2 is NG (*1 is OK) (for RHD)
Both *1 and *2 are NG



Both *1 and *2 are OK

*1 is NG (*2 is OK)

REPLACE TRANSPONDER KEY ECU ASSEMBLY

*2 is NG (*1 is OK) (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*2 is NG (*1 is OK) (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Both *1 and *2 are NG

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-8 (IND) - G43-21 (LP) Always Below 1 Ω
G88-8 (IND) - Body ground Always 10 kΩ or higher
G43-21 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-22 (IND) - G43-21 (LP) Always Below 1 Ω
G79-22 (IND) - Body ground Always 10 kΩ or higher
G43-21 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU OR TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Disconnect G88 transponder key ECU assembly connector.


c.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-8 (IND) - G43-21 (LP) Always Below 1 Ω
G79-22 (IND) - G43-21 (LP) Always Below 1 Ω
G88-8 (IND) - Body ground Always 10 kΩ or higher
G79-22 (IND) - Body ground Always 10 kΩ or higher
G43-21 (LP) - Body ground Always 10 kΩ or higher
G43-13 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPLACE TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE TELLTALE LIGHT ASSEMBLY
a.

Temporarily replace the security indicator light (telltale light assembly) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL


b.

When the immobiliser is set or the theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG



OK

END (SECURITY INDICATOR LIGHT [TELLTALE LIGHT ASSEMBLY] WAS DEFECTIVE)

NG

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.



b.

When the immobiliser is set or the theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)