When the power back door cannot be opened or closed using the back door control switch, one of the following may be malfunctioning: 1) back door control switch circuit, 2) multiplex network door ECU or 3) main body ECU (multiplex network body ECU).
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Check the Data List to determine if the back door control switch functions properly.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open SW | Back door control switch signal | ON or OFF | ON: Back door control switch pushed
OFF: Back door control switch not pushed |
- |
| Tester Display |
|---|
| Back Door Open SW |
The back door control switch functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the multiplex network door ECU with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the initialization for the multiplex network door ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check that the power back door operates normally.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| Power back door operates normally |
| Power back door does not operate |
Power back door operates normally
Power back door does not operate
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the back door control switch.
for LHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for LHD)>REMOVAL
for RHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for RHD)>REMOVAL
Inspect the back door control switch.
for LHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for LHD)>INSPECTION
for RHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for RHD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for LHD)>REMOVAL
for RHD: Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH(for RHD)>REMOVAL
Disconnect the G73 back door control switch connector.
Disconnect the G79 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-4 (MSW) - G79-27 (PBDS) | Always | Below 1 Ω |
| G73-1 (MSE) - Body ground | Always | Below 1 Ω |
| G73-4 (MSW) or G79-27 (PBDS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG