CLEARANCE WARNING ECU ASSEMBLY
Disconnect the G33 clearance warning ECU assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-11 (IG) - G33-16 (E) | G - W-B | Telltale light assembly (clearance sonar main switch) power source signal | Ignition switch ON, telltale light assembly (clearance sonar main switch) on | 11 to 14 V |
| G33-11 (IG) - G33-16 (E) | G - W-B | Telltale light assembly (clearance sonar main switch) power source signal | Ignition switch ON, telltale light assembly (clearance sonar main switch) off | Below 1 V |
| G33-16 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G33 clearance warning ECU assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-1 (BBZ) - G33-2 (ER) | LG - GR | No. 1 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(See waveform 1) |
| Buzzer not sounding | 11 to 14 V | |||
| G33-7 (L1) - G33-16 (E) | V - W-B | Rear corner sensor RH indicator signal | Clearance warning indicator LED for rear corner sensor RH illuminates | Below 3 V |
| G33-8 (L2) - G33-16 (E) | P - W-B | Rear corner sensor LH indicator signal | Clearance warning indicator LED for rear corner sensor LH illuminates | Below 3 V |
| G33-10 (L10) - G33-16 (E) | BR - W-B | Vehicle LED indicator signal | Clearance warning indicator LED for vehicle LED illuminates | Below 3 V |
| G33-12 (BOR) - G33-16 (E) | R - W-B | Power source for rear sensor circuit | Ignition switch off | Below 1 V |
| Ignition switch ON, clearance sonar main switch on | 7.2 to 8.8 V | |||
| G33-13 (E1) - G33-16 (E) | W - W-B | Ground rear clearance sonar | Always | Below 1 V |
| G33-14 (SOR) - G33-16 (E) | P - W-B | Rear sensor communication signal (Rear corner sensor) | Ignition switch ON, telltale light assembly (clearance sonar main switch) on, shift lever in R | Pulse generation
(See waveform 2) |
| G33-20 (TL) - G33-16 (E) | BR - W-B | Illumination signal | Ignition switch ON, light control switch off | Below 1 V |
| Ignition switch ON, light control switch on | 11 to 14 V | |||
| G33-21 (RL) - G33-16 (E) | V - W-B | Reverse signal | Ignition switch ON, shift lever in R | 7 V or higher |
| Ignition switch ON, shift lever not in R | Below 1 V | |||
| G33-23 (L3) - G33-16 (E) | L - W-B | Rear center sensor indicator signal | Clearance warning indicator LED for rear center sensor illuminates | Below 3 V |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G33-13 (E1) - G33-16 (E) |
| Tool Setting | 2 V/DIV., 500 μsec./DIV. |
| Vehicle Condition | When sonar detects obstacle (buzzer sounds) |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G33-14 (SOR) - G33-16 (E) |
| Tool Setting | 5 V/DIV., 1 msec./DIV. |
| Condition | Ignition switch ON, telltale light assembly (clearance sonar main switch) on, shift lever in R |