Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM3090E _59 Vehicle Exterior _008793 SLIDING ROOF / CONVERTIBLE _0050546 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

w/o Center Bracket:

i.

Temporarily install the sliding roof housing sub-assembly with the 8 nuts.

B338926N01
5.031,2.438 5.313,2.646 0.281,0.208 10 (2) 4.094,2.74 4.344,2.958 0.25,0.219 10 (8) 2.604,3.031 2.854,3.25 0.25,0.219 10 (4) 2.073,2.781 2.323,3 0.25,0.219 10 (6) 1.448,2.417 1.698,2.635 0.25,0.219 10 (5) 1.063,2.188 1.313,2.406 0.25,0.219 10 (3) 0.792,0.792 1.042,1.01 0.25,0.219 10 (7) 3.083,1.344 3.333,1.563 0.25,0.219 10 (1)


ii.

Tighten the nuts in the order indicated in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


iii.

Temporarily install the 4 bolts on the vehicle interior side.

B338925N01
4.573,0.865 4.792,1.063 0.219,0.198 10 (1) 4.156,0.365 4.375,0.563 0.219,0.198 10 (2) 3.333,0.354 3.552,0.552 0.219,0.198 10 (6) 2.917,0.844 3.135,1.042 0.219,0.198 10 (5) 2.917,1.75 3.135,1.948 0.219,0.198 10 (7) 3.333,2.229 3.552,2.427 0.219,0.198 10 (8) 4.156,2.24 4.375,2.438 0.219,0.198 10 (4) 4.573,1.74 4.792,1.938 0.219,0.198 10 (3)


iv.

Tighten the bolts in the order indicated in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

w/ Center Bracket:

i.

Temporarily install the sliding roof housing sub-assembly with the 8 nuts.

B341378N01
2.958,1.729 3.417,1.927 0.458,0.198 10 (1) 0.583,1.177 1.042,1.375 0.458,0.198 10 (7) 1.135,2.604 1.594,2.802 0.458,0.198 10 (3) 1.521,2.823 1.979,3.021 0.458,0.198 10 (5) 2.115,3.125 2.573,3.323 0.458,0.198 10 (6) 2.667,3.427 3.125,3.625 0.458,0.198 10 (4) 3.906,3.188 4.365,3.385 0.458,0.198 10 (8) 4.917,2.906 5.375,3.104 0.458,0.198 10 (2)


ii.

Tighten the nuts in the order indicated in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


iii.

Temporarily install the 8 bolts on the vehicle interior side.

B341376N01
4.563,0.979 5.021,1.177 0.458,0.198 10 (1) 4.094,0.979 4.552,1.177 0.458,0.198 10 (9) 4.365,0.719 4.823,0.917 0.458,0.198 10 (2) 3.906,0.708 4.365,0.906 0.458,0.198 10 (11) 3.563,0.698 4.021,0.896 0.458,0.198 10 (12) 3.104,0.708 3.563,0.906 0.458,0.198 10 (6) 2.906,1.635 3.365,1.833 0.458,0.198 10 (7) 3.104,1.906 3.563,2.104 0.458,0.198 10 (8) 3.521,1.938 3.979,2.135 0.458,0.198 10 (16) 3.906,1.948 4.365,2.146 0.458,0.198 10 (15) 4.344,1.927 4.802,2.125 0.458,0.198 10 (4) 4.052,1.656 4.51,1.854 0.458,0.198 10 (13) 4.563,1.656 5.021,1.854 0.458,0.198 10 (3) 3.375,0.969 3.833,1.167 0.458,0.198 10 (10) 2.917,0.979 3.375,1.177 0.458,0.198 10 (5) 3.344,1.667 3.802,1.865 0.458,0.198 10 (14)


iv.

Tighten the bolts in the order indicated in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.
B338940C01
2.219,2.76 2.021,2.646 false 2.458,0.948 2.542,0.948 2.542,0.948 2.615,1.135 false 2.917,0.917 2.833,0.917 2.833,0.917 2.823,1.104 false 2.5,1.698 2.583,1.698 2.583,1.698 2.667,1.531 false 2.24,2.719 2.552,2.875 0.313,0.156 10 false *a 0.667,4.333 0.979,4.49 0.313,0.156 10 false *b 2.563,2.323 2.875,2.479 0.313,0.156 10 false *c 2.323,0.875 2.635,1.031 0.313,0.156 10 false *2 2.938,0.823 3.156,1 0.219,0.177 10 true *3 2.344,1.615 2.656,1.771 0.313,0.156 10 false *1
*1 Marking A
*2 Marking B
*3 Clamp
*a Lock Area
*b Front Side
*c Out Side


Insert the sliding roof drain hose.

HINT:
·

The hose should be inserted to the base of the drain pipe.

·

Make sure that marking A on the drain hose is facing toward the bottom of the vehicle.




d.

Attach the claw to connect the sliding roof drain hose.

NOTICE:
·

Make sure that the lock area of the clamp is facing toward the outside of the vehicle when installing the clamp.

·

Install the clamp on the side of marking B that is closest to the sliding roof housing.



HINT:

Use the same procedure for the other 3 sliding roof drain hoses.



Hide 66424 2.INSTALL REAR SIDE RAIL SPACER LH

Hide 66414A 3.INSTALL REAR SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 62180A 4.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63251H 6.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Install the sliding roof weatherstrip as follows:

i.

Align the alignment mark (blue) on the weatherstrip with the middle marks at the corners of the sliding roof panel sub-assembly as shown in the illustration.


ii.

Position the centers of the 2 joints of the sliding roof weatherstrip as shown in the illustration and install the weatherstrip.


iii.

Install the lip of the weatherstrip firmly.

B338941C01
3.125,2.667 3.125,2.25 3.125,2.25 2.958,2.25 true 4.448,2.833 4.563,2.563 4.563,2.563 4.719,2.563 false 5.573,2.865 5.719,2.552 5.719,2.552 5.875,2.552 false 6.594,2.802 6.677,2.521 6.677,2.521 6.833,2.521 false 0.688,2.667 0.688,2.25 0.688,2.25 0.854,2.25 true 4.771,0.719 5.5,1.083 5.5,1.083 5.667,1.083 true 3.75,0.25 3.917,0.25 3.917,0.25 4.813,0.656 true 3.344,2.854 3.396,3.26 3.396,3.26 3.552,3.26 false 0.448,2.844 0.5,3.25 0.5,3.25 0.656,3.25 false 3.948,1.292 4.26,1.448 0.313,0.156 10 *A 3.979,2.635 4.292,2.792 0.313,0.156 10 *B 0.865,2.188 1.177,2.344 0.313,0.156 10 *1 1.844,3.24 2.156,3.396 0.313,0.156 10 *2 3.594,0.188 3.906,0.344 0.313,0.156 10 *3 5.698,1.01 6.01,1.167 0.313,0.156 10 *4 4.76,2.49 5.083,2.646 0.323,0.156 10 *a 5.885,2.479 6.198,2.635 0.313,0.156 10 *b 6.875,2.427 7.115,2.604 0.24,0.177 10 *c 2.76,2.198 3.073,2.354 0.313,0.156 10 *1 3.594,3.188 3.917,3.344 0.323,0.156 10 *d 0.667,3.177 0.99,3.333 0.323,0.156 10 *d
*A Normal *B Abnormal
*1 Center of Joint *2 Rear
*3 Alignment Mark (Blue) *4 Middle Mark
*a Pinched *b Exposed
*c Gap (raised, wavy, etc.) *d 46.6 cm (1.53 ft.)




Hide 63201G 7.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

B338942N01
2.25,2.115 2.406,2.313 0.156,0.198 10 B 1.813,2.115 1.969,2.313 0.156,0.198 10 A 1.552,2.115 1.708,2.313 0.156,0.198 10 A 2.531,2.104 2.688,2.302 0.156,0.198 10 B 1.771,1.021 1.927,1.219 0.156,0.198 10 C 1.781,1.281 1.938,1.479 0.156,0.198 10 C 2,2.51 2.156,2.708 0.156,0.198 10 D 2.167,2.719 2.323,2.917 0.156,0.198 10 D 4.938,1.438 5.094,1.635 0.156,0.198 10 a

i.

Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.

Standard:
Area Measurement
A - A 0 + 1.0 mm (0 + 0.0394 in.)
0 - 2.0 mm (0 - 0.0787 in.)
B - B 0 + 2.0 mm (0 + 0.0787 in.)
0 - 1.0 mm (0 - 0.0394 in.)
C - C 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.5 mm (0 - 0.0591 in.)
D - D 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.0 mm (0 - 0.0394 in.)


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.




c.
B338943C01
0.927,1.25 1.24,1.406 0.313,0.156 10 *a
*a Even


Perform a gap check.

i.

Check the gap between the roof panel and roof glass.

NOTICE:

The gap must be even all around.




d.

After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 8.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leaks.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218M 9.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Attach the 2 claws and install the sliding roof side garnish LH.


Hide 63217K 10.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63310 11.INSTALL ROOF HEADLINING ASSEMBLY

Hide 12.RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

Hide 14.INSPECT FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, inspect for water leaks.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.