Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM3090E _59 Vehicle Exterior _008793 SLIDING ROOF / CONVERTIBLE _0050546 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  DISASSEMBLY  


PROCEDURE

Hide 63260A 1.REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B338927
0.615,1.094 0.75,1.094 0.75,1.094 0.75,0.885 false 0.313,0.865 0.406,0.865 0.406,0.865 0.406,0.698 false 0.125,0.781 0.438,0.938 0.313,0.156 10 *1 0.417,1.021 0.729,1.177 0.313,0.156 10 *2
*1 Guide
*2 Pin


Detach the claw.


b.

Detach the guide and pin, and remove the map light bracket.


c.
B338928

Remove the 2 bolts and sliding roof drive gear sub-assembly.


Hide 63306 2.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
B338929

Remove the screw and the sliding roof piece sub-assembly LH.

HINT:

Use the same procedure for the RH side.



b.

Slide and remove the sunshade trim sub-assembly.

B341379
0.438,0.042 0.75,0.198 0.313,0.156 10 *A 3.781,0.083 4.094,0.24 0.313,0.156 10 *B
*A w/o Center Bracket *B w/ Center Bracket



Hide 63214F 3.REMOVE REAR ROOF DRIP CHANNEL

a.

Using a screwdriver, detach the 2 claws. Then slide the rear roof drip channel rearward to remove it.

B341381
4.938,0.479 4.76,0.479 false 1.76,0.49 1.583,0.49 false 1.51,2.146 1.385,2.146 false 4.719,2.177 4.594,2.177 false 0.354,0.073 0.667,0.229 0.313,0.156 10 *A 3.573,0.073 3.885,0.229 0.313,0.156 10 *B 1.229,2.073 1.542,2.229 0.313,0.156 10 *1 1.781,0.417 2.094,0.573 0.313,0.156 10 *1 4.979,0.385 5.292,0.542 0.313,0.156 10 *1 4.438,2.104 4.75,2.26 0.313,0.156 10 *1
*A w/o Center Bracket *B w/ Center Bracket
*1 Protective Tape - -


HINT:

Tape the screwdriver tip before use.



Hide 63205A 4.REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

NOTICE:

Do not disassemble the sliding roof drive cable sub-assembly except when replacing it.


a.
B338932

Hold down the roof wind deflector panel sub-assembly.


b.
B338933
1.375,1.646 1.583,1.646 1.583,1.646 2,1.406 false 1.104,1.583 1.417,1.74 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, slide the sliding roof drive cable sub-assembly in the direction indicated by the arrow in the illustration to remove it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other sliding roof drive cable sub-assembly.




Hide 63209 5.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B338934
2.573,1.438 2.406,1.438 false 2.396,1.875 2.229,1.875 false 0.542,0.292 0.646,0.292 0.646,0.292 0.646,0.427 false 0.24,0.438 0.344,0.438 0.344,0.438 0.344,0.573 false 0.385,0.208 0.698,0.365 0.313,0.156 10 *1 0.073,0.375 0.385,0.531 0.313,0.156 10 *2 2.229,1.365 2.542,1.521 0.313,0.156 10 *1 2.073,1.802 2.385,1.958 0.313,0.156 10 *2 1.833,0.146 2.146,0.302 0.313,0.156 10 (2) 0.708,1.844 0.927,2 0.219,0.156 10 (1)
*1 Spring
*2 Guide


Pull the spring in the direction indicated by the arrow (1) in the illustration to detach the 2 springs.


b.

Pull the roof wind deflector panel sub-assembly in the direction indicated by the arrow (2) in the illustration to detach the 2 guides and remove it.