Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor)
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050248 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Washer Signal Circuit  


DESCRIPTION

The headlight cleaner control relay receives the windshield washer operation signal.

WIRING DIAGRAM

E270837E01
5.229,1.24 5.896,1.427 0.667,0.188 10 false A48 5.25,1.427 6.365,1.802 1.115,0.375 10 false Headlight Cleaner Control Relay 0.177,2.229 1.688,2.479 1.51,0.25 10 false *1: for RH Side Type 3.344,0.75 4.01,0.938 0.667,0.188 10 false G61 1.51,1.24 3.073,1.604 1.563,0.365 10 false Windshield Wiper Switch Assembly 5.302,0.75 5.917,0.948 0.615,0.198 10 false FRWA 5.094,0.604 5.76,0.792 0.667,0.188 10 false 5 3.01,0.51 3.677,0.698 0.667,0.188 10 false 7 1.823,2.229 3.333,2.479 1.51,0.25 10 false *2: for LH Side Type 2.938,0.75 3.604,0.938 0.667,0.188 10 false G10 3.417,0.521 4.083,0.708 0.667,0.188 10 false 4 2.573,0.75 3.24,0.938 0.667,0.188 10 false WF 2.979,0.958 3.646,1.146 0.667,0.188 10 false *1 3.365,0.958 4.031,1.146 0.667,0.188 10 false *2

PROCEDURE

1.CHECK OPERATION
a.

Check the operation of the front wiper and washer system.


Result:
Proceed to
Front wiper and washer system operates normally
Front wiper and washer system does not operate



Front wiper and washer system operates normally

2.CHECK HEADLIGHT CLEANER CONTROL RELAY

Front wiper and washer system does not operate

2.CHECK HEADLIGHT CLEANER CONTROL RELAY
a.
E270952C01
0.25,0.646 0.563,0.958 0.313,0.313 0.26,1.135 0.573,1.448 0.313,0.313 0.979,1.854 1.208,1.854 1.208,1.854 1.396,1.438 true 2.521,1.854 2.177,1.854 2.177,1.854 1.99,1.448 true 0.104,0.063 0.417,0.26 0.313,0.198 10 *a 0.281,0.719 0.74,0.917 0.458,0.198 10 G10 0.281,1.219 0.74,1.417 0.458,0.198 10 G61 0.667,0.729 1.125,0.927 0.458,0.198 10 *A 0.667,1.188 1.125,1.385 0.458,0.198 10 *B 2.573,1.792 3.25,2 0.677,0.208 10 WF*A 0.531,1.771 1.208,1.979 0.677,0.208 10 WF*B
*A for RH Side Type
*B for LH Side Type
*a Front view of wire harness connector
(to Windshield Washer Motor and Pump Assembly)


Disconnect the windshield wiper switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH Side Type
Tester Connection Switch Condition Specified Condition
G10-7 (WF) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

for LH Side Type
Tester Connection Switch Condition Specified Condition
G61-4 (WF) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - WINDSHIELD WIPER SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - WINDSHIELD WIPER SWITCH ASSEMBLY)
a.

Disconnect the A48 headlight cleaner control relay connector.


b.

Disconnect the G10*1 or G61*2 windshield wiper switch assembly connector.

*1: for RH Side Type

*2: for LH Side Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH Side Type
Tester Connection Condition Specified Condition
A48-5 (FRWA) - G10-7 (WF) Always Below 1 Ω
A48-5 (FRWA) - Body ground Always 10 kΩ or higher

for LH Side Type
Tester Connection Condition Specified Condition
A48-5 (FRWA) - G61-4 (WF) Always Below 1 Ω
A48-5 (FRWA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT CLEANER CONTROL RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR