Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor)
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050248 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

The headlight cleaner control relay controls the headlight cleaner motor and pump assembly.

WIRING DIAGRAM

E270597E01
2.156,1.198 3.385,1.396 1.229,0.198 10 false H-LP CLN 3.229,1.24 3.688,1.438 0.458,0.198 10 false A47 3.219,1.417 4.688,1.76 1.469,0.344 10 false Headlight Cleaner Motor and Pump Assembly 2.052,0.594 4.042,0.792 1.99,0.198 10 false ECU-IG NO.3 4.969,2.354 6.917,2.719 1.948,0.365 10 false Headlight Cleaner Control Relay 4.979,2.156 5.438,2.354 0.458,0.198 10 false A48 5.573,1 5.885,1.198 0.313,0.198 10 false PB 5.573,0.427 5.885,0.625 0.313,0.198 10 false IG 5.573,1.76 5.885,1.958 0.313,0.198 10 false E 5.344,0.323 5.656,0.521 0.313,0.198 10 false 3 5.354,0.885 5.667,1.083 0.313,0.198 10 false 6 5.365,1.615 5.677,1.813 0.313,0.198 10 false 4 0.677,1 2.51,1.198 1.833,0.198 10 false from Battery 0.167,0.427 3.229,0.625 3.063,0.198 10 false from IG1 NO.2 Relay 3.563,0.885 3.875,1.083 0.313,0.198 10 false 2 4.146,0.885 4.458,1.083 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.

Remove the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL


b.

Inspect the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND BATTERY)

NG

REPLACE HEADLIGHT CLEANER WASHER MOTOR AND PUMP ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND BATTERY)
a.

Disconnect the A47 headlight cleaner motor and pump assembly connector.


b.

Disconnect the A48 headlight cleaner control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 - A48-6 (PB) Always Below 1 Ω
A47-1 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
a.
E139345C03
1.448,0.385 1.865,0.677 0.417,0.292 1.99,1.208 2.271,0.354 2.271,0.354 2.427,0.354 true 1.146,1.906 1.333,1.906 1.333,1.906 1.427,1.542 true 2.406,1.927 2.156,1.927 2.156,1.927 1.979,1.552 true 0.104,0.094 0.417,0.292 0.313,0.198 10 *a 2.49,0.292 3.104,0.49 0.615,0.198 10 IG 1.531,0.458 1.99,0.656 0.458,0.198 10 A48 1.01,1.823 1.625,2.021 0.615,0.198 10 E 2.458,1.844 3.073,2.042 0.615,0.198 10 PB
*a Front view of wire harness connector
(to Headlight Cleaner Control Relay)


Disconnect the headlight cleaner control relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-4 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A48-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR